Table of Contents
Advertisement
FRONT PANEL FACILITIES
@® input selector buttons
VCR 1
: Press when performing playback on a first VCR unit.
VCR 2
: Press when performing playback on a second VCR
unit.
VIDEO
: Press
when
performing
playback
on
a VCR
connected to VIDEO INPUT jacks on the front panel.
TV/SAT
: Press when using a TV tuner connected to the TV/
SAT jacks.
LD
: Press when performing playback on an LD player.
TAPE 1
: Press when
performing
playback
on a cassette
deck.
TAPE 2 MONITOR
: Press when
performing playback on a second
cassette deck and when monitoring recording.
PHONO
: Press when playing records on turntable.
TUNER
: Press when listening to radio broadcasts.
cD
: Press when playing compact discs on a CD player.
© DIRECT button
Press this to listen to source sound without passing the audio signa!
through sound quality and balance adjusting circuitry.
The surround mode, super bass, and rear and center speakers are
automatically switched off.
@ MULTI-JOG
Use
during
tuner
operation
to select frequencies
and
station
numbers. During GUI operation, use to move the on-screen cursor.
SUPER BASS button
Switch on when you want to boost bass. This does not operate when
the DIRECT button is on.
© MUTING button
Press to temporarily cut off the sound volume. When pressed again,
the sound will return to its previous level.
@ RETURN button
Press this button to return the receiver into the initial state. TUNER is
selected at this initial state. Adjust the sound level by using the
MASTER VOLUME control.
@ TAPE 2 MONITOR
OFF
eFUNCTION
.
® SURROUND MODE .
OFF
@V-SIGNAL SELECTOR
®MUTING
|... native OFF.
And SPEAKERS buttons switch as follows.
TUNER
wee OFF
Before pressing the
RETURN button
Both A and B are off
Only Ais on
After pressing
Only A is on
No change
Both A and B are on
Only Bis on
Both A and B are on
No change
NOTE;
Press the RETURN
button,
and the frequency last selected is
received. /f reception of a station is not possible with that frequency,
the mode automatically switches ta AUTO TUNING.
@ MASTER VOLUME control
Use it to simultaneously adjust the sound volume from the front,
center, and rear speakers.
© SPEAKERS buttons (A, B)
ON/OFF switches for the A and B speaker systems. (Indicator in the
display section lights.)
® PHONES jack
Connect the plug on your headphones to this jack. Set the surround
mode and ail SPEAKERS A and B switches to OFF if you want to cut
the
sound
from
speakers
and
listen
to it only through
the
headphones.
® VIDEO INPUT jacks
VIDEO components such as a VCR or TV camera, etc. can be
connected.
@ REC SEL (Recording Selector) button
You can select the component to be recorded from, en VCR 1 without
using the input selector.
Each time you press the REC SEL button, the components change in
the following order.
7— TAPE 1 -» PHONO —» TUNER -»CD —VCR 2
> VIDEO 7
off +
iD <
TV/SAT «
When the REC SELECTOR
has been through all the components
once, REC SELECTOR switches off.
@ GUI MODE button (See page 38)
Switches GU! MODE on and off.
@ MULTI-ROOM & SOURCE button
Use in combination with the separately sold MR-100 Multi-Room
remote control unit.
When this button is on, the source selected with the input selector at
thattime is set to the Sub room function. The selected sub-function's
sound is output through SUB ROOM
SPEAKERS,
and the video
signal is output through the MULTI-ROOM VIDEO OUT jack. If you
install speaker systems connected to the MULTI-ROOM SPEAKERS
terminals in a different room, you can enjoy different sources in two
different rooms with a single main unit.
@ Display section (See page 21)
.
2
<ARB1489>
Advertisement
Table of Contents
