Technical Data - Engine Tightening Torques - KTM 250 SX-F EU 2011 Owner's Manual

TECHNICAL DATA - ENGINE TIGHTENING TORQUES

Jet, crank chamber ventilation
Oil jet for alternator cooling
Oil jet, conrod lubrication
Screw, stator
Oil jet for cam lever lubrication
Screw, ignition pulse generator
Screw, locking lever
Screw, oil filter cover
Screw, oil pump cover, left
Screw, oil pump cover, right
Locking screw for bearing
Screw, alternator cover
Screw, cable holder in alternator cover
Screw, clutch cover
Screw, clutch slave cylinder
Screw, clutch spring
Screw, cover plate of valve cover
Screw, cylinder head
Screw, engine case
Screw, exhaust flange
Screw, kickstarter stop
Screw, shift drum locating
Screw, shift lever
Screw, timing chain securing guide
Screw, timing chain tensioning rail
Screw, valve cover
Screw, water pump cover
Oil jet, piston cooling
Nut, camshaft bearing bridge
Screw, camshaft bearing bridge
Stud, camshaft bearing bridge
Plug, crankshaft location
Screw, kickstarter
Screw, timing chain guide rail
Screw, cylinder head
Screw, engine sprocket
Spark plug
Rotor screw
Screw, unlocking of timing chain ten-
sioner
Screw, camshaft gear
Engine coolant temperature sensor
Oil drain plug with magnet
Plug, oil pressure regulator valve
Plug for oil screen, short
M4
M4
M4
M4
M5
M5
M5
M5
M5
M5
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6x0.75
M7
M7
M7
M8
M8
M8
M10
M10
M10
M10x1
M10x1
M12x1
M12x1.5
M12x1.5
M12x1.5
M16x1.5
2 Nm (1.5 lbf ft)
2 Nm (1.5 lbf ft)
2 Nm (1.5 lbf ft)
4 Nm (3 lbf ft)
4 Nm (3 lbf ft)
6 Nm (4.4 lbf ft)
6 Nm (4.4 lbf ft)
6 Nm (4.4 lbf ft)
6 Nm (4.4 lbf ft)
5 Nm (3.7 lbf ft)
6 Nm (4.4 lbf ft)
10 Nm (7.4 lbf ft)
6 Nm (4.4 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
3 Nm (2.2 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
14 Nm (10.3 lbf ft)
8 Nm (5.9 lbf ft)
8 Nm (5.9 lbf ft)
10 Nm (7.4 lbf ft)
10 Nm (7.4 lbf ft)
4 Nm (3 lbf ft)
15 Nm (11.1 lbf ft)
15 Nm (11.1 lbf ft)
2 Nm (1.5 lbf ft)
20 Nm (14.8 lbf ft)
25 Nm (18.4 lbf ft)
10 Nm (7.4 lbf ft)
Tightening sequence:
Tighten diagonally, begin-
ning with the rear screw on
the chain shaft.
Step 1
40 Nm (29.5 lbf ft)
Step 2
50 Nm (36.9 lbf ft)
60 Nm (44.3 lbf ft)
10... 12 Nm (7.4...
8.9 lbf ft)
70 Nm (51.6 lbf ft)
10 Nm (7.4 lbf ft)
80 Nm (59 lbf ft)
12 Nm (8.9 lbf ft)
20 Nm (14.8 lbf ft)
20 Nm (14.8 lbf ft)
10 Nm (7.4 lbf ft)
84
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
–
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
–
®
Loctite 243™
–
–
–
®
Loctite 243™
–
–
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
®
Loctite 243™
–
–
®
Loctite 243™
Lubricated with engine oil
Lubricated with engine oil
®
Loctite 243™
–
®
Loctite 243™
®
Loctite 243™
Lubricated with engine oil
®
Loctite 243™
–
Thread, oiled with engine
oil/cone degreased
–
®
Loctite 243™
–
–
–
Lubricated with engine oil