Setting The Maximum Frequency; Setting The Plot Storage Requirements - Agilent Technologies WireScope 350 User Manual

@‘ƒr…‡ÃH‚qrÃs‚…Ã8‚ƒƒr…ÃUr†‡vt
UurÃ@‘ƒr…‡Ã6ˆ‡‚‡r†‡ÃTr‡ˆƒ

Setting the Maximum Frequency

Setting the Plot Storage Requirements

6−16
6 The last Measurements Setup screen allows you to skip the automatic
fault location calculation. This does not prevent you from using the
locator in the Results Details function, but prevents the calculation
on each test, including the passing tests. When this selection has been
made, press Next to return to the Autotest Settings screen.
The WireScope 350 allows you to select the maximum range for swept
frequency measurements. The choices depend somewhat on the
standard selected previously, for example for Category 6, the 100 MHz
choice is not available. To set the maximum frequency:
1 In Expert Mode, press Autotest on the Main menu.
2 On the Autotest Setup screen press Edit Settings. On the Autotest
Settings screen press Max Frequency. On the Frequency Setup
screen select the maximum frequency of the data being stored.
1RWH UurÃ…rh†‚Ã‡‚Æryrp‡Ã‡urÃy‚r†‡Ãs…r„ˆrp’Ãv†Ã‡‚Ãqrp…rh†rÇr†‡Ã‡v€rÃhqÃqrp…rh†rÀr€‚…’Ã
†‡‚…htrÃUurÃhqqv‡v‚hyƒ‡v‚hyÃqh‡hÃv†Ãs‚…Ãvs‚…€h‡v‚Ã‚y’ȁyr††Ã’‚ˆÃv†uÇ‚Ã…r†r…‰rÃ
‡urÃqh‡hÃs‚…††viyrÃyh‡r…Ã…rpr…‡vsvph‡v‚Ãh‡ÃhÃuvtur…Ãs…r„ˆrp’Ƈhqh…qÐv‡uÃTp‚ƒr9h‡hÃ
Q…‚Æ‚s‡h…rÃhÃQ8ÃDsÃ’‚ˆÃuh‰rÁ‚‡Ã†h‰rqÇurÃuvtur…Ãs…r„ˆrp’Ãqh‡hÇurÃ
…rpr…‡vsvph‡v‚Ã€h’Á‚‡ÃirÃh‰hvyhiyrÃA‚…Ãr‘h€ƒyrÃvsÃ’‚ˆÃ‡r†‡Ã‡‚ÇurÃ8h‡rt‚…’Ã$@Ã8yh††Ã
9Ƈhqh…qÃiˆ‡Ãuh‰rÃyv€v‡rqÃ’‚ˆ…Àh‘v€ˆ€Ãs…r„ˆrp’Ç‚à ÃHC“ÇurÃ’‚ˆÃvyyÁ‚‡ÃirÃ
hiyrÇ‚Ã…rpr…‡vs’Ãyh‡r…Ðv‡uÇurƇ‚…rqÃqh‡hÇ‚Ã8h‡rt‚…’Ã%Ã8yh††Ã@ÐuvpuÃ…r„ˆv…r†Ãqh‡hÃ
‡‚Ã!$ÃHC“
Another storage choice is available, whether to save plots or not. Saving
plots stores the entire swept frequency measurement. Summary data is
the worst case value for each test and is the minimum required for
standards compliance. To set the data being stored:
1 In Expert Mode, press Autotest on the Main menu.