Rear Panel Features; Installation; Step 1: Get Ready - Extron electronics Decorator-Style Series Setup Manual

Rear Panel Features

LAN (Ethernet) and PoE connector and LEDs — Connect the unit to a network via this connector for control and Power over
Ethernet. Use the following diagrams as a guide. All NBP one-gang decorator-style models have identical rear panel features.
LAN/PoE
(Ethernet)
connector
and LEDs
Rear Panel Features
Figure 4.
ATTENTION:
•
Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only to networks or circuits that are not
routed to the outside plant or building.
•
L'alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement. Elle doit être connectée
seulement à des réseaux ou des circuits qui ne sont pas routés au réseau ou au bâtiment extérieur.
IMPORTANT NOTES:
•
The factory configured passwords for this device have been set to the device serial number. Passwords are case sensitive.
Performing a Full Factory Reset (see
•
DHCP is off by default.

Installation

Step 1: Get Ready

Use the following check list to prepare for the installation.
Download and install the latest versions of the software, firmware, and device drivers needed to configure or program the
•
control processor to interact with the NBPs and control the connected AV products. See the user guide for the device
(available at www.extron.com) for details on software and drivers.
Obtain network information for the unit from the network administrator. You need the following details for each IP Link Pro
•
device, including the control processor and each NBP:
DHCP setting (on or off)
•
Device (NBP) IP address
•
NOTE:
If DHCP is on, you do not need the IP addresses and subnet mask.
Write down the MAC address of each IP Link Pro device (such as the NBP) to be used.
•
Obtain model names and setup information for the AV devices to be controlled in the system.
•
Each NBP button panel comes with a factory-installed Secure Sockets Layer (SSL) security certificate. If you intend to install
•
a different SSL certificate, contact your IT department to obtain the certificate or for instructions on how to obtain one.
See "Secure Sockets Layer (SSL) Certificates" in the Network Button Panels User Guide for requirements and guidelines
regarding SSL certificates.
Activity LED:
MAC Address
Blinks
amber to
indicate data
is being sent
or received.
PC
Figure 5.
Reset Modes: a Brief Summary
Subnet mask
•
Gateway IP address
•
NBP Rear Panel
Link LED: Lights
LAN/PoE
green to indicate a
network connection.
RJ-45
Connector
Ethernet
Extron
TCP/IP
Network Control
Processor
LAN/PoE Port Details
on page 9) sets the passwords to extron.
•
•
LAN/PoE (Ethernet and
Power Over Ethernet)
Connect to an Ethernet network.
This port must be con gured.
Default protocol:
• NBP address: 192.168.254.253
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• Link speed and duplex level: autodetected
• Data rates: 10/100Base-T
Power over Ethernet (PoE):
The NBP receives power at this port.
Default login credentials:
• Username: admin or user
• Initial password: unit serial number
• Password after a "Full Factory Reset":
extron
NOTE: MAC address information
(00-05-A6-XX-XX-XX) is located
on the rear of each decorator-style
enclosure.
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: XXXXXXX EXXXXXX
MAC
Address
MAC: 00-05-A6-XX-XX-XX
S/N: XXXXXXX EXXXXXX
User name
Passwords
3