Direct Vent System; Installation Configuration - Drolet ECO-55 Installation Manual

4.5 DIRECT VENT SYSTEM

In Canada: The permitted termination locations for a
direct vent system are the same than those permitted
with a regular pellet vent system.
In the Unites States : The permitted termination
location for a direct vent system are the same than
those permitted with a regular pellet vent system
H[FHSW IRU WKH IROORZLQJ 7KH H[LW WHUPLQDO VKDOO EH
located not less than 9" (23 cm) from any opening
through which vent gases could enter a building.

4.6 INSTALLATION CONFIGURATION

4.6.1 THROUGH WALL INSTALLATION (MAIN
)/225 25 %$6(0(17
1. Position appliance following clearances vent
manufacturer's instructions.
2. Install a stove adapter or a stove adapter tee onto
WKH DSSOLDQFH ÀXH FROODU
3. /RFDWH WKH SRVLWLRQ RI WKH H[KDXVW SLSH LQ WKH ZDOO
and cut a hole of the appropriate size for vent in
the wall.
4. Install wall thimble as per vent manufacturer's
instructions.
5. Ensure you install enough horizontal pipe length
WR H[FHHG WKH H[WHULRU ZDOO RI  LQFKHV ,QVWDOO D
tee section to the pipe passing through the wall.
6. Run the vent vertically up the wall for at least
36". Refer to the vent manufacturer's instructions
for clearances to combustible materials and
installation of wall bands.
7. Install a 90 degrees elbow facing out from the
wall and then attach a 45 degree elbow facing
towards the ground. The termination of the vent
must include a spark arrester, fastened to the 45
degrees elbow.
8. Sealed
outside wall
temperature waterproof silicone sealant.
Page 12
thimbles with high
INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST
4.6.2 7+528*+ 522) ,167$//$7,21
1.
Position appliance following clearances and
following vent manufacturer's instructions.
2.
Install a stove adapter or a stove adapter tee
RQWR WKH DSSOLDQFH ÀXH FROODU ,I QHFHVVDU\ XVH
D KRUL]RQWDO DGGLWLRQDO OHQJWK EHWZHHQ WKH ÀXH
outlet and the tee.
3.
Drop the plumb line over the center of the tee
outlet and mark location on the ceiling.
4.
&XW D KROH IRU DSSURSULDWH FHLOLQJ VXSSRUW )UDPH
rough opening.
5.
,QVWDOO FHLOLQJ VXSSRUW DQG WKH ¿UVW YHQW VHFWLRQ DV
per vent manufacturer's instructions.
6.
,QVWDOO D ¿UHVWRS UDGLDWLRQ VKLHOG RQ DQ\
VXEVHTXHQW FHLOLQJÀRRU H[FHSW IRU WKH DWWLF
where an attic insulation shield is required.
7.
Run the necessary section of vent vertically so
WKH UDLQ FDS H[FHHGV WKH KLJKHVW SRLQW RI WKH URRI
at least 24" in United States and at least 36" in
Canada.
8.
Install roof support.
9.
,QVWDOO URRI ÀDVKLQJ DQG UDLQ FDS DV SHU
manufacturer's instructions. If necessary, install
a storm collar.