Table of Contents
Advertisement
3 Introduction
Thank you for choosing this product. The Edel Air Source
Heat Pump water heaters are specified with high quali-
ty, immersion heaters for fast reheat times. They boast
50mm of low GWP insulation foam, together with 100%
recyclable stainless steel inner components and a hard
wearing outer shell manufactured from completely recy-
cled materials.
Dimplex cannot take responsibility for
ensuring safe operation of the appliance
outside of the scope of intended use.
3.1 Dimplex Control
This product is Dimplex Control capable * .
Control and monitor your heating and hot water with Dim-
plex Control. Group appliances into zones to easily control
and track their energy usage. Any time. Anywhere.
Search for Dimplex Control on your device's app store.
*A Dimplex Hub is required for this product to connect to
Dimplex Control. For instruction on setting up Dimplex Hub,
please refer to the manual online or section 9 in this manu-
al. Manuals can be downloaded at www.Dimplex.co.uk.
4 Scope of Delivery
The appliance is delivered factory fitted with a T&P valve
and immersion heater. The tripod is contained within the
same package as the appliance. For the installation, two ac-
cessories boxes are required and are provided by Dimplex.
A complete list of all items delivered is illustrated in Table 1
Cylinder with 1.2Kw immersion
T+P valve
Tripod
Inlet control group consisting of:-
- In line strainer
- 3 bar PRV
- 6 bar ERV
- Non-return valve
- Balanced cold water supply port
- Connection for expansion vessel
Expansion vessel with fixing kit and connection hose
Tundish
EDL Vent kit consisting of -
Ø
-
80mm MF PVC elbow
Ø
-
125mm sleeve 850mm
Ø
-
80mm flexible tube 250mm
Ø
-
80mm PVC ducting 1000mm
Ø
-
125mm PVC ducting 400mm
Ø
-
125mm half tee
- Tee cover
Ø
-
125mm insulated extension 850mm
- Wall seal ring
- Collar
- Vent nozzle
- Exterior seal
- Drilling template
Installation & user instructions x 1
Terms and conditions x 1
Table 1: Scope of Delivery for Edel Water Heater
Note:
This product has been designed specifically for the
purpose of delivering heated, domestic and sanitary
hot water as part of a pressurised water heating
system. The package is provided with fittings that
comply with Section G3 of Building Regulations.
5 Pre-Installation Advice
Please read the following section carefully before
commencing installation. If in any doubt, please call the
appropriate help desk. Disregarding the instructions given
in this manual in its entirety and any relevant regulations,
standards and codes of practice will void the guarantee of
this product.
5.1 Handling
The upper covers of the appliance are not made to
withstand force and should not be used for
handling purposes.
If tipped, the centre of gravity will shift
towards the top: handle with care.
Please note that handling, installation and use of this prod-
uct is subject to the Health and Safety at Work Act.
If the unit is not installed immediately, it should remain in
its protective packaging with all pipe protectors/end caps
applied to prevent damage and dirt deposit inside the wa-
ter heater and the coil.
Pre-Installation
Non-permitted transport positions:
Transporting the appliance in a
horizontal position may lead to
!
irreparable damage to the
components of the heat pump
Permitted transport positions:
Transport and handling of the appliance
must be done in its original cardboard
packaging using the handles integrated
into the cardboard packaging for ease of
transportation.
Transport in a vehicle must be done with
the appliance in a vertical position.
All other transport positions are
!
PROHIBITED
Risk of tipping/falling
Do not drop
or lower suddenly
5
Advertisement
Table of Contents
