Table of Contents
Advertisement
Rinsing
Use this function to deliver hot water from the coffee spout (A8)
and from the hot water spout (C3), if inserted, to clean and heat
n
the appliance's internal circuit. Place a container with a mini-
mum capacity of 100ml under the coffee and hot water spout.
-
To enable the function, proceed as follows:
1. Press the
2. Press
3. Press the
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the
.
ered first from the coffee spout and then from the hot water
spout (if inserted) which cleans and heats the appliance' s
internal circuit.
y
Please note!
•
To stop delivery at any time, press any icon.
•
If the appliance is not used for more than 3-4 days, we strong-
ly recommend, when switching on the appliance, performing
2/3 rinses before using it.
Descaling
For instructions on descaling, see page 18.
.
Install filter
For Instruction for use on how to install the filter, see the section
"Water softener filter" (page 20).
e
Replacing the limescale filter (if installed)
For Instruction for use on how to replace the filter, see the sec-
tion "Replacing the filter" (page 20).
g
Adjust time
n
To adjust the time on the display, proceed as follows:
1. Press the
2. Press
3. Press the
4. Press
5. Press the
6. Press
l
7. Press the
This sets the time. Press the
icon (B2) to enter the menu;
or
(fig. 5) until "Rinsing" is displayed;
icon (fig.6), "Confirm?" is displayed;
icon: after a few seconds, hot water is deliv-
icon (B2) to enter the menu;
or
(fig. 5) until "Adjust time" is displayed;
icon (fig. 3). The hours flash on the display;
or
to change the hour;
icon to confirm. The minutes flash;
or
to change the minutes;
icon to confirm.
icon to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or
(fig. 5) until "Auto-start" is displayed;
3. Press the
button (fig. 3). "Enable?" is displayed;
4. Press the
icon to confirm;
5. Press
or
to choose the hour;
6. Press the
icon to confirm;
7. Press
or
to change the minutes;
8. Press the
icon to confirm;
9. Press the
icon to exit the menu.
Once the time has been confirmed, activation of auto-start is
indicated by the
symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the
icon. "Disable?" is displayed;
3. Press the
icon to confirm.
The
symbol is no longer displayed.
Auto-off (standby)
Auto-off can be set so that the appliance goes off after 15 or
30 minutes, or 1, 2 or 3 hours. To programme Auto-off, proceed
as follows:
1. Press the
(B2) icon (B2) to enter the menu;
2. Press
or
(fig. 5) until "Auto-off" is displayed;
3. Press the
icon (fig. 6);
4. Press
or
until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the
icon to confirm;
6. Press the
icon to exit the menu.
Auto-off is programmed.
Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or
displayed;
11
(fig. 5) until "Energy Saving" is
Advertisement
Table of Contents
Troubleshooting
