Step 6: Wipe Out Inside Of Dryer; Step 7: Plug In The Dryer - Speed Queen SFET07 Installation And Operation Manual

Installation
8. Using screwdriver, remove two door plugs, and
reinstall on opposite side of door opening.
Figure 29
9. Reinstall four hinge attaching screws, removed in
Step 1.
Figure 30

Step 6: Wipe Out Inside of Dryer

Before using dryer for the first time, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside dryer drum.
Figure 31
24
NS
IO
CT
RU
IN ST )
TI NG at set ting
e (he ES S, t)
RA PR hea
O PE bric , PE Typ RM F (no
t Fa AL FL UF
lec Se NO RM AT E,
1. LIC rt.
DE s. Sta
the . Pu sh
d Clo ard or and or.
2. Loa in(s )/C Do en Do
Co Clo se - Op Sta rt.
Ins ert er - cle Pu sh
3. rt Dry ring Cy or and
To Sta er Du Do
4. p Dry Clo se Wh en
Sto er - lete
5. To rt Dry is Co mp Off . AD
Re sta ht Go es LO
To Cy cle Lig R EA CH
6. Dry ing nel TE
Pa R AF
TE
T FIL
N LIN
EA
CL
504 210
E
LIC AT E
DE US
IN
S
PR ES UF F AT )
RM FL O HE
PE (N
OR
AL CT
RM LE
NO IC SE
BR
FA
T
AR
ST
TO
SH
PU
D385I
D385i
D606I
D606I
NS
IO
CT
RU
IN ST )
IN G at set S, ting
AT e (he PR ES hea t)
ER Typ RM (no
OP Fab ric AL, PE FLU FF
Sel ect RM AT E,
1. NO LIC rt.
DE s. h Sta
the . Pus
d Clo )/C ard or and or.
Loa 2. in(s se Do en Do rt.
ert Co er - Clo le - Op h Sta
3. Ins rt Dry Cyc Pus
Sta er Du ring Do or and
To 4. p Dry se en
Sto er - Clo lete Wh
5. To rt Dry Co mp Off . AD
Re sta le is ht Go es CH LO
To 6. ing Cyc el Lig R EA
Dry Pan TE
R AF
T FIL TE
LIN
EA N
CL
210
504
E
AT E
DE LIC US
IN
S )
PR ES UF AT F
RM FL HE
PE (NO
AL CT OR
RM LE
NO IC SE
BR
FA
AR T
ST
TO
SH
PU
D621I
D621I
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Step 7: Plug In the Dryer

Electric Dryer
Connect the dryer to an electrical power source. Refer
to Step 4 for information on connecting power cord.
Connect to 30 Amp circuit.
Figure 32
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and
comes equipped with a 3-prong grounding plug. Refer
to serial plate for specific electrical requirements.
NOTE: The wiring diagram is located inside the
control hood.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer's responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
When plugging in the dryer:
• Do not overload circuits.
• Do not use an adapter.
• Do not use an extension cord.
• Do not operate both a washer and gas dryer on
the same circuit. Use separately fused 15 Amp
circuits.
D275I
W521
510977