Table of Contents
Advertisement
No.
Item
60
Function of stop immedi-
ately after reverse feed
stitching at the start of
sewing
64
Change-over speed of
condensation stitch or
EBT (end back tack)
70
Function of soft-down of
presser foot
71
Double reverse feed
stitching function
72
Sewing machine startup
selecting function
73
Retry function
*
76
One-shot function
84
Initial motion suction
time of presser foot
lifting solenoid
87
Function of pedal curve
selection
90
Initial motion up stop
function
91
Function of prohibiting
compensation operation
after turning handwheel
by hand
92
Function of reducing
speed of reverse feed
stitching at the start of
sewing
93
Function added to nee-
dle up/down compensat-
ing switch
95
Head selection function
96
Max. sewing speed
*
103 Needle cooler output
OFF delay time
120 Main shaft reference
angle compensation
121 Up position starting
angle compensation
122 DOWN position starting
angle compensation
*
150 Correction of the thread
clamp speed at the start
of sewing
*
151 Thread clamp ON angle
*
152 Thread clamp OFF
angle
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time of
delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated. If it is necessary to
change the set value, please purchase the Engineer's Manual and follow the instructions.
Description
Function at the time of completion of reverse feed stitching at the start of
sewing
0 : Not provided with the function of temporary stop of the sewing ma-
chine at the time of completion of reverse feed stitching at the start
of sewing
1 : Provided with the function of temporary stop of the sewing machine
at the time of completion of reverse feed stitching at the start of
sewing
Initial speed when starting condensation stitch or EBT
Presser foot is slowly lowered.
0 : Presser foot is rapidly lowered.
1 : Presser foot is slowly lowered.
Effective/ineffective of double reverse feed stitching is changed over.
(Only used when the CP-18 is used.)
0 : Ineffective
1 : Effective
Current limit at the startup of sewing machine is specified.
0 : Normal (Current limit is applied during startup.)
1 : Rapid (Current limit is not applied during startup.)
This function is used when needle cannot pierce materials .
0 : Retry function is not provided.
1 to 10 : Retry function is provided. (Setting of the needle bar returning
force)
One-shot operation up to the material end is specified.
0 : One-shot operation is not performed.
1 : One-shot operation is performed.
Suction motion time of presser foot lifting solenoid
Pedal curve is selected. (Improving pedal inching operation)
2
Sewing speed
0
Automatic UP stop function is set immediately after turning ON the
power.
0 : OFF
1 : ON
It is effective in combination with the machine head provided with tension
release function.
0 : Tension release function is ineffective.
1 : Tension release function is effective.
Function to reduce speed at the time of completion of reverse feed stitch-
ing at the start of sewing.
0 : Speed is not reduced.
1 : Speed is reduced.
Operation of needle up/down compensating switch is changed after
turning ON the power or thread trimming.
0 : Normal (Needle up/down compensating stitching only)
1 : One stitch compensating stitching is performed only when aforemen-
tioned changeover is made. (Upper stop / upper stop)
Machine head to be used is selected.
(When the machine head is changed, each setting item is changed to the
initial value of the machine head.)
Max. sewing speed of the sewing machine head can be set. (The MAX
value differs by machine head.)
Delay time from the stop of sewing machine to the output OFF is speci-
fied using the needle cooler output function.
Main shaft reference angle is compensated.
Angle to detect UP position starting is compensated.
Angle to detect DOWN position starting is compensated.
Speed correction coefficient for the function of the thread clamp at the
start of sewing is set.
The angle at which the thread clamp is turned ON at the start of sewing
is set.
The angle at which the thread clamp is turned OFF at the start of sewing
is set.
1
Pedal stroke
– 38 –
Setting range
Default
page
0/1
0
0 to 250
1 8 0
(sti/min)
0/1
0
0/1
1
0/1
0
0 to 10
1
0/1
0
50 to 500
1 0 0
(ms)
0 to 2
0
0/1
1
0/1
1
0/1
0
0/1
0
The setting
150 to MAX
differs with the
(sti/min)
machine head.
100 to 2000
5 0 0
(ms)
–50 to 50
- 1 3
–15 to 15
5
–15 to 15
0
10 to 200
1 0
180 to 290
2 1 0
(°)
210 to 359
2 9 0
(°)
Ref.
47
47
48
48
48
48
48
48
49
49
49
49
Advertisement
Table of Contents
