Page 1
Owners Manua Door Opener 39°535006 CAUTION: READ INSTRUCTIONS FOR SAFE OPERATION FASTEN THIS MANUAL NEAR THE GARAGE DOOR AFTER INSTALLATION° PERIODIC CHECKS OF OPENER ARE REQUIRED TO INSURE SATISFACTORY OPERATION,, Features Specifications You'll Need Safety Rules Carton Check Accessories Identify Your Door Assembly AND RULES...
FEATURES OF YOUR OPENER 1o Opener Lights: Turn on and off automatically, with 4-1/2 minute illumination for your safety and convenience. Provide constant light when Work Light control button is pressed.. 2,. Safety System: Independent up and down force adjustment.. Door reverses automatically structed in DOWN...
Page 3
THIS SAFETY ALERT SYMBOL MEANS STRUCTION., READ THESE INSTRUCTIONS THIS GARAGE DOOR OPENER IS DESIGNED PROVIDED IT IS INSTALLED SAFETY INSTRUCTIONS., FAILURE TO COMPLY WITH THE INJURY OR PROPERTY DAMAGE,. KEEP GARAGE DOOR BALANCED.. STICKING OR BINDING DOORS MUST BE REPAIRED.. GARAGE DOORS, DOOR SPRINGS,...
Page 4
CARTON CHECK LIST SEARS has packaged your Garage Door Opener three-piece rail, two hanging straps, straight THE OPENER CARTON CONTAINS: Opener Chassis Plastic Light Lenses Transmitter and Clip (1) Chain & Cable (in dispenser carton)* 2-Piece Trolley* *ILLUSTRA'T'ED BELOW Inner Chain &...
Page 5
PROCEDURES OCCUR, SURE FOLLOW i CONSTRUCTION Includes visor clip,, CODE LOCK: Enables homeowner to open the garage door opener from the by entering code on specially designed KEY SWITCH: Opens the garage door automatically is not handy Provides an illuminated...
Page 6
Assembmy TO AVOID INSTALLATION DIFFICULTIES, COMPLETED STEP 8, PAGE 15. STE P I Assemble Tee Rail & Attach Cable Pulley Bracket ,.,,i CAUTION: Do not tighten the lock necks are seated in square holes° Tee Rail (Center Section Flange 1/4" Lock Nut _/'_"...
Page 7
Assemb v S=_E Connect As a temporary stop, insert a screwdriver rail as shown. Slide the inner trolley onto the Tee rail, as shown, until it is firmly against the screw- driver, Slide the outer trolley onto the Tee rail until it partially engages the inner trolley and stops TO FULLY ENGAGE TROLLEY: With a hammer, firmly tap the back end of outer trolley just below the...
Page 8
Assembly Master Link CabIe Notch CAUTION: Keep chain taut while carton to help prevent kinking° Slide trolley tight against screwdriver cable around pulley bracket. Proceed the opener sprocket and forward bracket. Be sure teeth on chassis chain. Connect chain to chain retainer bracket, inset, using second master link from coin envelope...
Page 9
Ass÷mbUv OAUTIONt Keep chain from twisting turned, Loosen Tighten Inner Lock Washer Trolley Chain Base of Tee Rail STEP Sprocket Cover ASSEMBLY OF YOUR GARAGE CERTAIN INSTALLATION PROCEDURES ENCES OCCUR, BE SURE TO FOLLOW CONSTRUCTION,, DO NOT WEAR WATCHES, RINGS KEEP GARAGE DOOR BALANCED.
Page 10
Instalaation Completed installations of header bracket, door bracket with plate and door arm (depending below.. The header bracket supports IT IS RECOMMENDED THATTH E OPENER PERMITS. Follow only those instructions STEP 1 TO PREVENT DAMAGE TO LIG HTWEIGHTGARAGE BOTH VERTICALLY AND HORIZONTALLYMWITH Horizontal brace should be at least 6 feet tong Verticat brace should cover height of top panel.
Page 11
nstanUation S=_E THE HEADER BRACKET MUST BE RIGIDLY WALL OR CEILING WITH 2x4 IF NECESSARY,, Locate height for header bracket by opening highest point of travel as shown. Draw a horizontal line on header wall 2" above high point provides travel clearance for top edge of door When...
Page 12
nstamlation STEP 3 Clevis 5/t6"'x2-3/4- Bracket Cable Pulley" B_acket Packing STE P 4 TO PREVENT DAMAGE TO ALL OPENER ON THE DOOR.. SECTIONAL and ONE-PIECE DOOR WiTH TRACK nN STA LL&_ II0 N NOTE: A 2x4 is convenient for setting door-to-Tee rail distance, it is not...
Page 13
UnstaIlation STEP 5 THE OPENER CHASSIS MUST BE ATTACHED STRUCTURAL SUPPORT OF THE GARAGE representative installations are shown_Yours different, Hanging brackets should be angled to pro- vide rigid support, PROCEDURE: On EACH side of opener the distance from chassis to structural Cut both pieces of the hanging bracket...
Page 14
_nsta_lation Flange Wall Control Bo|tom Terminals Installation Flange Right Side Antenna Panel Opener Vacation Work Light Push Button Push Button Wall Control Push Button INSTALL "WALL CONTROL PUSH BUTTONS) OUTOFTHE DREN,_ DO NOT ALLOW WALL CONTROL SERIOUS PERSONAL GARAGE DOOR MISUSE OF OPENER°...
Page 15
0nstatUation STEP 8 TO AVOID SERIOUS PERSONAL INJURY FROM ENTANGLEMENT, GARAGE DOOR BEFORE OPERATING DOOR OPENER_ REMOVE EXISTING GARAGE DOOR LOCKS OR USE A WOOD SCREW OR NAIL TO MAKE THE_,_ INOPERATIVE, INSTALLATION AND WIRING MUST BE IN COMPLIANCE WITH LOCAL BUILDING AND ELECTRICAL CODES. OPERATION AT OTHER THAN !2OV 6OHz WILL CAUSE OPENER MALFUNCTION IF LOCAL ELECTRICAL CODES...
instal|ation ...:r,, ,, SECTIONAL PROCEDURE: Fasten straight door arm section trolley and wedge door arm section as shown (A)Insert and spread a cotter pin to secure each connection_ _ .___ ,/II ,ov,s ,n Do,,, I_1--- Straight INSTALLATION FOR SECTIONAL ALL ONE-PIECE ASSEMBLE DOOR ARM PROCEDURE: straight and wedge door arm sections together to...
Page 17
nstam ation STE P 11 CAUTION: To prevent damage to garage the opener limits must be adjusted PIECE DOORS, Limit Adjustment settings regulate which door will stop when moving Repeated operation of the opener during adjustment may cause the motor to overheat and shut off.
Adjustment STEP 1 ,, ,, _ ,, ... ,,,, The limit adjustment screws are located on the left side panel of the opener chassis settings regulate the points at which NOTE: Door STOPS in U P direction tion if anything interferes with door travel (including PROCEDURE:...
Page 19
STEP 2 DO NOT USE FORCE ADJUSTMENTS EXCESSIVE FORCE WILLINTERFERE OR DAMAGE THE GARAGE DOOR. Force Adjustment Controls are located on right side panel of the opener chassis,, FORCE ADJUSTMENT settings regulate the amount of power open and close the door NOTE: Door STOPS...
Page 20
THE SAFETY REVERSE SYSTEM WITH A ON E 1NC H OBSTAC LE PLACED ON TH E FLOOR. RESULT IN SERIOUS PERSONAL ONCE A YEAR AND MAKE ANY NEEDED PROCEDURE: Place a 1-inch obstacle direction,. The door must reverse on the obstruction if a SECTIONAL door STOPS on the obstruction,...
Operation of Your Opener CAUTION: ® START B Y READING THE SAFETY RULES ON PAGE 3. e READ THE OPERATING INSTRUCTIONS e DO NOT PERMIT CHILDREN TO PLAY IN AREA OF DOOR. e OPERATE ONLY WHEN OPENER IS PROPERLYADJUSTEDAND THE SAFETY REVERSE SYSTEM TACTWITH...
Radio Controls RECEIVER Anger Right Side Panel THE TRANSMITTER The portable transmitter may be secured visor with the clip provided Additional can be purchased at any time for use in all vehicles using the garage (Refer to Accessories, New transmitters must be set to the same code as original transmitter...
Page 23
Radio ControlJs Sears Td nanj Radio ControJ Manutactured ut_der ! or more The coded signal in Sears Trinary Radio Controls needed is a flat blade screwdriver, Choose the receiver code switch block., Changing -- MATCHING The original transmitter is preset at the factory NEW transmitters must be set to match the code...
Page 24
OPENER DOESN'T ACTIVATE 1. Have you removed all door locks and bolts? 2 Does the opener have electric power? Check wait switch, fuse, etc. 3. is there a broken wire between Walt Control opener? Check under staples, (A positive can be made by temporarily instalb_g another wire) 4., Are wiring connections...
Repair Parts RAI L ASSEMBLY PARTS LIST INSTALLATION PARTS LIST NO,. DESCRIPTION PART 41D2736 Wall control assy 10A13 9 volt battery (available Transmitter case, cover 41A2830 29C121_2 Transmitter visor ctip 41A2828 Emergency rope and handle 4-Strand belt wire 2t9A319 41A2829 Header bracket Door bracket...
Page 27
Repair Parts Assembmy Parts List Chassis PART DESCRIPTION 31C290 Sprocket cover 4IA2827 Gear and sprocket assy Complete with: Spring washer Thrust washer Retaining ring Bearing plate Roll pins (2) Drive gear Worm gear Helical gear w/retainer Grease 41A28t7 Drive/worm gear kit w/grease Roll pins (2) 41 B2991 Line cord...
From the 91st day untii one year from the date of purchase, Sears will furnish replacement par ts for any defective parts, free of charge.. You pay for labo After 1 year and through 5 years, if the motor on this Garage Door Opener is defective, Sears will furnish a replacement motor, free of charge.. You pay for labor.