FEATURES OF YOUR OPENER Motor: Permanently lubricated with automatic reset, Opener Light: Turns on and off automatically. Provides 4-1/2 minute illumination and convenience, Safety System: Independent up and down force adjustment. Door reverses automatically obstructed in DOWN direction Door STOPS when obstructed in UP direction EasyLimitAdjustment:...
CARTON CHECK LIST SEARS has packaged yourGarage Door Opener illustrated below and on Page 22. Sprocket Rail Cover Grease SEPARATE ALL HARDWARE FOR ASSEMBLY ASSEMBLY HARDWARE Lockwasher 5116"(3) Washered Master Link 5/16 "_ 18 Carriage Bolt _f _ 1/4''_20xl/2" 5/16"-18x7/8" Lock Nut 1/4"...
Start By Reading These Impo ant THIS SAFETY ALERT DAMAGE INSTRUCTION. THIS GARAGE DOOR SAFE SERVICE PROVIDED WITH TH E FOLLOWING FAILURE TO COMPLYWITH PERSONAL INJURY CAUTION: IF YOUR GARAGE HAS NO SERVICE KEYLOCK (PAGE 2). THIS ACCESSORY POWER FAILURE. KEEP GARAGE DOOR BALANCED°...
NOT make ANY further operation can be IS NOT THE TRANSMITTER: more than one garage door opener, push buttons may also be used to operate trol devices. Transmitter(s) with clip(s) provided. Additional door will stay at any time...
Assembly TO AVOID INSTALLATION DIFFICULTIES, INSTRUCTED TO DO SO. _: P "1 Assemble CAUTION: Do not tighten the lock nuts until bolt necks are seated in square holes. The center rail section MUST be positioned on the LEFTSIDE of end rails as shown, Otherwise, trolley will hit against nut when installed (Pg.
Page 7
Assernbiy STE P 2 Install As a temporary stop, insert a screwdriver hole in front end of Tee rail as shown. inner trolley onto the Tee rail until it is firmly against the screwdriver NOTE: If trolley hits against nut on Tee rail, center section was attached from wrong...
Page 8
Assembly STE P 4 DO NOT REMOVE CHAIN AND CABLE FROM CARTON Detach cable from side of carton and fasten to trolley with a master link from coin envelope MASTER LINK PROCEDURE: Push pins of master link bar through loop of cable and hole in flat end of trolley shaft (A) Push cap over pins and onto notches.
Assembly STE P 5 Loosen Tighten Inner Outer Trolley Chain Base of Tee Rail " ASSEMBLY OF YOUR GARAGE BEFORE YOU PROCEED WITH THE INSTALLATION COMPLY WITH THE FOLLOWING KEEP GARAGE DOOR BALANCED. GARAGE DOOR, THE DOOR SPRINGS, MAY BE UNDER EXTREME A'FFEM PTADJUSTM ENTS.
installation STE P 1 Installation procedures vary according your door as illustrated below., THE HEADER BRACKET REINFORCE WALL OR CEILING 1 With door closed, locate and mark the vertical centerline of garage door Extend line onto header wall above door 2, Locate height for header bracket to highest point of travel as shown,...
Page 11
installation STE P 2 Clevis 5/16 'x2-3/4 STE P 3 Follow instructions TO PREVENT DAMAGE NOT REST THE OPENER SECTIONAL and ONE-PIECE DOOR WiTH TRACK I NSTALLATION NOTE: A 2x4 is convenient for setting door-to-Tee rail distance. It is not necessary headroom is insufficienL PROCEDURE:...
Page 12
installation STEP 4 THE OPENER CHASSIS MUST BE SECURELY Three representative installations (Fig. 1 ) or crossed (Fig. 2) to provide rigid support (not supplied) to ceiling joists before installing opener PROCEDURE: On EACH side of opener measure the distance from chassis to structural Cut both pieces of the hanging...
Page 13
A con- venient place is beside the service door and OUT OF THE REACH OF CHILDREN, Run the bell wire up the wall and across the ceiling to garage door opener Use insulated staples to secure wire, The receiver terminals and the antenna are located on the back panel of the opener chassi&...
Page 14
Installation STE P 7 PROCEDURE: Install a light bulb, (75 Watts imum) in socket as shown The light will turn on and remain lit for 4-!/2 minutes when power is connected After 4-1/2 minutes it will turn off If light bulb burns out prematurely tion,...
Page 15
Installation STE P 9 Follow instructions TO PREVENT DAMAGE OF DOOR--BOTH VERTICALLY Horizontal brace should be at least 6 feet long Vertical brace should cover height of top panel is to check with your garage door manufacturer Sectional SECTIONAL DOOR Vertical _ Center_._ _ Line...
Page 16
installation STE P 10 Follow only SECTIONAL FIG, A. Make sure garage door is closed straight door arm section to trolley with a clevis pin. Secure with a ring or cotter pin fastener(if cotter to secure) Fasten curved section to door bracket FIG,, B.
Adjustment STEP 1 LIMIT ADJUSTMENT settings regulate the door will stop when moving up or down NOTE: Door STOPS in UP direction direction if anything interferes with door travel (includ- ing binding or unbalanced doors). fereswithdoortraveI. The door REVERSES button or transmitter.
Adjustment STEP 3 TH E SAFETY REVERSE ON CONTACT WITH A ONE INCH PERLY ADJUST OPENER GARAGE DOOR. REPEAT TEST AT LEAST FOUR TIMES PROCEDURE: Place a 1-inch obstacle The door must reverse on the obstruction If a SECTIONAL door STOPS on the obstruction, lengthen door arm until the door reverses...
Radio Controls Your 3-channel transmitter(s) will operate more than one garage door opener, if desired, Also, refer to the catalog packed with your opener for remote light products which can be operated by the additional push buttons on the transmitter(s).
1 Is there a neighborwith a garage door opener using the same frequency code? Change your code Review Page 19. 2. Check to makesure that the transmitter push button(s) is not stuckin the 'down' position 3.
Page 21
Having a Problem? (Continued) SITUATION i ,i I DOOR WON'T CLOSE DOOR REVERSES NO APPARENT REASON OPENER LIGHT OPENER STRAINS MAXIMUM FORCE IS NEEDED TO OPERATE DOOR OPENER MOTOR HUMS BRIEFLY, THEN WON'T OPENER WON'T OPERATE DUE TO POWER FAILURE CHAIN DROOPS OR SAGS...
Repair Parts RAI L ASSEMBLY PARTS LIST ',"sTAL-L_,T,0" PA41:sLisi: i.o. NO. DESO,,PT,O, ' 41 D2736-1 Wall control assy l i iiiiis !;iii!=iiii'!s, °r 41 A2828 Emergency rope and handle 2119A3223 H-e_dandrb_Wlrplu 11_374 DD°°rr brr:Ckk:tt plate ,_ tg%OO,,HO3O_gingbrooko,s . 41A2815 Installation hardware PART 1A995...
41 A3076 End panel w/all labels NOT SHOWN 41A2825 Chassis not designated block w/screws replacement motor Model 139,53413 13953606 Model 139.53403 gear & retainer w/grease switch assembly assembly assy with plug bracket and bearing assy cup assy. logic board assy...
Center and most Sears, Roebuck and Co stores Be sure to provide all pertinent facts when you call or visit, The MODEL NUMBER of your garage door opener is printed on a label located on the front panel of the opener chassis.