Advertisement
QUICK START GUIDE
Avoid running your model in tall grass or soft sand. These will strain the
power system. If the model becomes stuck, do not apply throttle.
Free the model before operating it.
The TQ 2.4GHz transmitter has a directional antenna. For maximum range,
hold the transmitter upright and pointed in the direction of the model.
Pointing the transmitter away from the model will reduce radio range.
Transmitter Adjustments
Steering Trim
Slowly turn the steering trim knob to precisely set the steering
neutral point. To adjust, drive the vehicle forward slowly while
"steering" with the trim knob until the vehicle travels in a
straight line with no steering input.
Electronic Speed Control Adjustments
ATTENTION: IF USING A LiPo BATTERY
To prevent over-discharging of LiPo batteries, Low-Voltage Detection
must be switched on. To check the status of your model, turn it on. If the
speed control's LED is green, Low-Voltage Detection is already activated. If
the LED is red, Low-Voltage Detection is not active. Follow these steps to turn
on Low-Voltage Detection:
1. Turn the model on. Make sure the LED on the speed
control is on and red.
2. Press and hold the EZ-Set button for ten seconds. The
LED will turn off and then light green, and the motor
will beep twice. Release the button.
3. Low-Voltage Detection is now ACTIVATED.
LiPo batteries are intended only for the most advanced
users that are educated on the risks associated with
LiPo battery use.
WARNING: FIRE HAZARD!
Do not use LiPo batteries in this vehicle with
Low-Voltage Detection disabled.
To disable Low-Voltage Detection when using NiMH batteries, repeat the steps
above. The motor will beep three times and the LED will glow red.
Selecting a Throttle Mode: SPORT, RACE, or TRAINING
1. Connect a fully charged battery to the model and turn on your transmitter.
2. With the model off, press and hold the EZ-Set button until the LED turns
solid green, then solid red, and then begins blinking red. It will blink once,
then twice, then three times, then repeat.
One blink = Sport Mode is the default setting. It allows full forward and
reverse throttle.
Two blinks = Race Mode removes reverse throttle in case your track does
not allow it.
Three blinks = Training Mode will slow the model down by 50% for
young or inexperienced drivers.
3. Release the EZ-Set button after the number of blinks for the mode you
wish to select. Note: If you missed the mode you wanted, keep the EZ-Set
button pressed down and the blink cycle will repeat.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED). The model is now ready
to drive.
30 • STAMPEDE 4X4
Calibrating the Speed Control
The speed control is calibrated at the factory. If the LED on the speed control
is flashing green, then follow these steps to recalibrate it.
1. Connect a fully charged battery to the model.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A).
The LED will first turn green and then red.
Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull the
throttle trigger to the full throttle position
and hold it there (B).
5. When the LED blinks RED TWICE, push
the throttle trigger to the full reverse and
hold it there (C).
6. When the LED blinks GREEN ONCE,
programming is complete. The LED will
then shine green or red (depending on
Low-Voltage Detection setting).
Running in Wet Conditions
Your Traxxas model is designed with water-resistant features to protect the
electronics in the model (receiver, servos, electronic speed control). Though
highly water resistant, the model should not be treated as though it is
submersible or totally, 100% waterproof. Water resistance applies only to the
installed electronic components. Running in wet conditions requires additional
care and maintenance to prevent corrosion and maintain proper function.
Download the complete manual for full precautions and maintenance
requirements. Read and understand all precautions before operating your
A
model in wet conditions. The complete manual for your model can be viewed
and downloaded by following the link on the cover of this manual or by
scanning the QR code. Please read this entire manual for complete instructions
on the proper use and maintenance of your model.
Red LED: Hold 10 seconds
After You Run Your Model
B
Turn the model off
Press and release the EZ-Set button on the speed control.
The speed control's LED will go out.
Unplug the battery and remove it from the model
2 Beeps: LED shines green
Do not store the model with the battery installed.
Turn the transmitter off
Always turn the transmitter off last, after the model has been turned off.
Turn off the model.
1
2
Unplug the battery.
A
Green then Red
B
Once Red
C
Twice Red
3
Always turn your
transmitter off last.
Advertisement
