Advertisement
QUICK START GUIDE
The following guide is an overview of the procedures for getting your
model running. The complete manual for your model can be viewed
and downloaded by following the link on the cover of this manual or
by scanning the QR code. Please read the entire manual for complete
instructions on the proper use and maintenance of your model.
Read the Safety Precaution
For your own safety, understand where carelessness and misuse could lead
to personal injury and product damage.
Prepare Your Model
Selecting a charger and batteries for your model
Your model does not include a battery or charger. The speed control in the
model is compatible with both LiPo and NiMH batteries. One NiMH or 2s
LiPo battery equipped with a Traxxas High-Current Connector is required.
Traxxas Power Cell iD batteries are strongly recommended for maximum
performance and safer charging. The following chart lists available Power
Cell iD batteries for your model:
LiPo Batteries with iD
2843X
5800mAh 7.4V 2-Cell 25C LiPo Battery
2854X
10000mAh 7.4V 2-Cell 25C LiPo Battery
NiMH Batteries with iD
2926X
Battery, Power Cell, 3000mAh (NiMH, 7-C hump, 8.4V)
2941X
Battery, Series 3 Power Cell, 3300mAh (NiMH, 7-C hump, 8.4V)
2951X
Battery, Series 4 Power Cell, 4200mAh (NiMH, 7-C hump, 8.4V)
2961X
Battery, Series 5 Power Cell, 5000mAh (NiMH, 7-C hump, 8.4V)
WARNING: FIRE HAZARD!
Users of Lithium Polymer (LiPo) batteries must read the
Warnings and Precautions beginning on page 2. You
MUST use a LiPo charger for LiPo batteries or battery damage
with the potential for fire will result.
Make certain you choose the correct type of charger for the batteries you
select. Traxxas recommends you choose a genuine Traxxas EZ-Peak iD
charger for safer charging and maximum battery life and performance.
NiMH
Charger
Part No.
Compatible
EZ-Peak Plus,
2970
4 amps
EZ-Peak Live,
2971
12 amps
EZ-Peak Dual,
2972
8 amps
EZ-Peak Live
2973
Dual, 26+ amps
Install batteries in the transmitter
The transmitter requires
4 AA alkaline or
rechargeable batteries.
LiPo
Battery
Compatible
iD
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
Install the battery pack in the model
Place the battery in the tray. Insert the
hold-down into the chassis as shown.
Secure by placing the clip into the post.
Compatible batteries:
• 6-7 cell NiMH
• 2-cell LiPo
ATTENTION: USERS OF
LiPo BATTERIES
Activate Low-Voltage Detection when
using LiPo batteries. Refer to the EZ-Set
Tips card attached to your model, or see
the Electronic Speed Control Adjustments
section of this guide.
Turning on Your Mode
Turn on the transmitter
Always turn the transmitter on first, before turning on the model.
The transmitter's LED will glow.
Plug the battery into the speed control
Align the + and – markings. Make certain the battery plug is
completely inserted.
Turn on the model
Press and release the EZ-Set button on the speed control. The speed
control's LED will glow.
1
Always turn your
transmitter on first.
Before Operating Your Model
Check servo operation
Max.
Confirm the model's wheels turn right and left when the transmitter
Cells
steering wheel is turned right and left. The front wheels should be pointing
straight ahead. If they are turned slightly, slowly adjust the steering trim
3s
control on the transmitter until they are pointing straight ahead.
Range test the radio system
4s
With a friend's help, check servo operation at a distance and that there is no
interference before running your model.
3s
Operating Your Model
4s
Note: After stopping the model, return the transmitter's trigger to neutral and
push up again to activate reverse throttle.
l
2
Plug in the battery.
Turn on the model.
Neutral
Brake/Reverse
Forward
STAMPEDE 4X4 • 29
3
Advertisement
