Page 2
ECM-2.5 ELECTRONIC Thank you again for going with Traxxas. We work hard every day Traxxas models are about experiencing total performance and CONTROL MODULE to assure you the highest level of customer satisfaction possible.
Page 3
Traxxas service needs. Maintenance and replacement Throughout this manual, you’ll notice warnings and helpful hints Ready-To-Drive, TQ, Titan, TRX-4M, parts may be purchased directly from Traxxas by phone or online and ECM-2.5 are trademarks or identified by the icons below. Be sure to read them! at Traxxas.com.
Page 4
All of us at Traxxas want you to safely enjoy your new model. Operate Electronic Control Module (ECM) your model sensibly and with care, and it will be exciting, safe, and fun Your model’s electronic control module (ECM) is an extremely powerful All instructions and for you and those around you.
Traxxas iD batteries. DO NOT use a non-Traxxas charger hobby dealer or contact the battery manufacturer. As a reminder, all to charge Traxxas iD batteries. It is not recommended, but if you batteries should be recycled at the end of their useful life.
Page 6
SAFETY PRECAUTIONS (continued from previous page) • ALWAYS charge batteries in a well-ventilated area. • Allow the battery pack to cool off between runs (before charging). • REMOVE flammable items and combustible materials from the • ALWAYS unplug the charger and disconnect the battery when not charging area.
Page 7
LiPo balance charger* ® Required Equipment (not included) Traxxas recommends genuine Traxxas iD® batteries and chargers for safer charging, maximum battery life, and performance. 4 AA alkaline batteries *Battery and charger style are subject to change and may vary from images.
MODEL OVERVIEW Chassis Top View Front Bumper Steering Tie Rod Chassis Rail Steering Block Electronic Control Module (ECM) Rear Bumper Mount Rear Bumper Front Shock Mount Steering Servo Motor Transmission Front Bumper Mount Caster Block (C-hub) Shock Batttery Tray Battery Strap Rear Shock Mount 8 •...
Page 9
MODEL OVERVIEW Chassis Bottom View Front Lower Front Upper Link Front Lower Link Rear Lower Link Rear Upper Link Rear Axle Cover Shock Mount Servo Horn Front Rear Drive Cup Drive Cup Front Center Driveshaft Rear Center Driveshaft Skidplate Rear Lower Shock Mount Front Axle Cover Front Axle...
Page 10
quick start: getting up to speed The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. The Quick Start Guide is not intended to replace the full operating instructions 1.
BEC (Battery Eliminator Circuit) - The BEC can either be in the receiver or is constricted, energy is converted to heat and is lost. Traxxas power in the ESC. This circuit allows the receiver and servos to be powered by systems are optimized to reduce electrical resistance and the resulting the main battery pack in an electric model.
Page 12
TRAXXAS TQ RADIO SYSTEM MODEL WIRING DIAGRAM ECM-2.5 Wiring Diagram Your model is equipped with the Traxxas TQ 2.4GHz transmitter. The transmitter has two channels: channel one operates the To Lights steering, and channel two operates the throttle. Your model is...
Warnings and Precautions beginning on page 4. ONLY use designed for use only with the the supplied Traxxas iD® LiPo balance charger to charge the included included Traxxas 2-cell LiPo iD Traxxas iD® battery. DO NOT charge LiPo batteries with a NiMH-only battery.
TRAXXAS TQ RADIO SYSTEM 3. Reinstall the battery compartment door and To reinstall the body: snap it closed. 1. Position the body on the chassis. Align the front and rear of the If the status LED doesn’t light body with the front and rear bumpers.
Page 15
TRAXXAS TQ RADIO SYSTEM RADIO SYSTEM CONTROLS Always turn your transmitter on first. Plug in the battery to turn on the model. Neutral Brake/Reverse Unplug the battery to turn off the model. Always turn your transmitter off last. • Always use new or freshly charged batteries for the radio system.
Page 16
TRAXXAS TQ RADIO SYSTEM TRANSMITTER LED CODES TQ 2.4GHz Binding Instructions For proper operation, the transmitter and ECM must be electronically LED Color / Pattern Name Notes ‘bound.’ This has been done for you at the factory. Should you ever...
® LIGHTING the EZ-Set button. Your new Traxxas model is enabled with Pro Scale® lighting features, 4. The LED will then turn solid green. The such as headlights, reverse lights, and brake lights. Visit Traxxas.com to model is ready to drive.
LiPo battery from being discharged below its safe minimum threshold Tips for Increasing Run Time (see page 16 for more information). When this happens, stop driving • ONLY use the supplied Traxxas iD® LiPo balance charger to charge the immediately, unplug the battery, and recharge. included Traxxas iD® battery.
Page 19
DRIVING YOUR MODEL • The transmitter is not water resistant. Do not subject it to wet 3. Blow off the truck with compressed air (optional, but conditions, such as rain. recommended). Wear safety glasses when using compressed air. • Do not operate your model during a rain storm or other inclement 4.
“bounce” after rebounding from a bump. Changing the oil in the shocks can vary the suspension damping effect. Changing the oil to Note: Traxxas offers SAE-20W silicone a higher viscosity oil will increase damping. Lowering the viscosity shock oil as part #5031 or a full silicone of the oil will cause the suspension damping to be reduced.
Page 21
TUNING ADJUSTMENTS Shock Assembly 1. Insert the shock shaft assembly through the shock body until the piston bottoms out. 2. Lubricate the shaft and o-rings with silicone oil. 3. Install the one o-ring over the shaft and into the bore of the shock body followed by one small black spacer, and then another o-ring.
1-888-TRAXXAS If the bottom of the shock is leaking, then it is time for a rebuild. The Traxxas rebuild kits for two shocks are part #9762 and 9762A. (1-888-872-9927) (U.S. residents only) • Suspension: Periodically inspect the model for signs of damage, such as bent linkage rods, bent shock shafts, loose screws, or any signs of stress or bending.