Table of Contents
Advertisement
2. Use the [] and [] keys to select the area that you
want to program the part mode 2 name for, then
press [OK] to select. Alternatively, you can enter the
area number that you want to program the name,
then press [OK].
The keypad will display the following:
Part Mode 2 Name A1
Part 2 Area 1 Name
Press
3. Use the [] and [] keys to scroll the cursor left and
right across the name text. Use the [] and [] keys
to scroll through the different characters available.
To clear all text from the cursor position to the right,
press the [OFF] key.
4. When the name is complete, press [OK].
Areas > Area Properties >
Auto Arming
This menu allows you to program which timezone will be
used by the system to auto arm and or, auto disarm the
system or area. Before setting this option you should make
sure the timezone has been configured in MENU 7-5-0.
Generally a timezone configured for auto arming should
be given a name that indicates its function.
The system has a maximum of 16 available timezones and
only one timezone can be programmed for each area. The
auto arm function can only be used to fully arm the area.
Only your installer can configure your system or area to
auto arm the area in part mode.
The area will automatically arm when the stop time in the
selected timezone is reached provided the day of the week
is also set.
The area will automatically arm when the stop time in the
selected timezone is reached provided the day of the week
is also set.
If auto disarming is not required then you should not set
the start time in the selected timezone. See MENU 7-5-0
for more information on configuring timezones.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [8].
A list of available areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the auto arm time for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program, then press [OK].
The keypad will display the following:
Bosch Security Systems 3/23 BLCC610U
OK to SAVE
MENU 2-1-8
Auto Arming A1
04 - TimeZone 4 Name
Press
3. Use the [] and [] keys to scroll through the list of
timezones until you reach the required one for the
chosen area.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Areas > Timers >
Exit Time
This menu allows the master user to modify the exit timer
for the selected area. Each area in the system can have a
different exit time if required. The exit time is the amount
of time you have to leave the area once it has been turned
on. The keypad will sound an exit warning beep during
this time to let you and other users know that the area is
arming. An alarm cannot be triggered until the exit time
has expired.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [8] + [0].
A list of available areas will display on the keypad.
A1 Reception Area
A2 Sales Dept
A3 Administration Dept
Press
2. Use the [] and [] keys to select the area that you
want to program the exit time for, then press [OK] to
select. Alternatively, you can enter the area number
that you want to program, then press [OK].
The keypad will display the following:
Exit Time A1
060 Seconds
Press 0-9 OK to SAVE
3. Use the numeric keys to enter the required time in
seconds and then press [OK]. Exit time can be set
from 0 to 255 seconds.
Areas > Timers >
Entry Time 1
This menu allows the master user to modify the entry timer
number 1 for the selected area. Each area in the system
can have a different entry time if required. Your installer
will have set up one or more entry zones per area on your
system and the zones may have been programmed to
follow either entry time 1 or entry time 2.
The entry time is the amount of time you have to turn your
alarm system off once the entry zone have been triggered
or opened.
Solution 6000
User Guide
0-9 OK to SAVE
MENU 2-8-0
OK or MENU
MENU 2-8-1
21
Advertisement
Table of Contents
