Heating Water; Preparation; Changing The Quantity; Cleaning - DeLonghi ESAM35 Series Instructions For Use Manual

into the cup and the message "COFFEE F. CAPPUCCINO
PROGRAM QUANTITY" is displayed.
6. As soon as the coffee in the cup reaches the required level,
press the button again. Coffee delivery stops.
The machine is now reprogrammed with the new quantities.

HEATING WATER

Preparation

Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water.
The hot water spout becomes hot while water is delivering and
must be handled by the handle only.
1. Place a container under the cappuccino maker (as close as
possible to avoid splashes) (fig. 4).
2. Press the button (fig. 2). The message "HOT
WATER" is displayed.
4. Water flows out of the spout. Delivery stops automatically
after 250ml.
5. To interrupt delivery of hot water manually, press the
button again.
Please note!
• You should not deliver hot water for more than 3 minutes
at a time.

Changing the quantity

The appliance is set by default to automatically deliver 250ml.
To modify these quantities, proceed as follows:
1. Position a container under the spouts.
2. Press the button until the message "HOT WATER
PROGRAM QUANTITY" is displayed.
• When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantities.

CLEANING

Important!
• Do not use solvents, abrasive detergents or alcohol to cle-
an the appliance. With De'Longhi superautomatic coffee
makers, you need not use chemical products to clean the
machine.
• None of the components can be washed in a dishwasher
apart from the milk container (B).
• Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.

Cleaning the coffee maker

The following parts of the machine must be cleaned regularly:
- coffee grounds container (A15),
- drip tray (A13),
- inside the machine, accessible after opening the service
door (A14),
- water tank (A10),
- coffee spouts (A16) and hot water nozzle (A9),
- pre-ground coffee funnel (A7),
- infuser (A18),
- milk container (B)

Cleaning the coffee grounds container

When "EMPTY GROUNDS CONTAINER" is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
Even if not full, the empty grounds container message is
displayed 72 hours after the first coffee has been prepared. For
the 72 hours to be calculated correctly, the machine must never
be turned off with the main switch in the 0 position.
• Open the service door on the front of the appliance (fig.
24), extract the drip tray (fig. 25), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.

Cleaning the drip tray

Important!
If the drip tray is not emptied regularly, the water could
overflow from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 26).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Open the service door (fig. 24);
2. Remove the drip tray and the grounds container (fig. 25);
3. Empty the drip tray and grounds container and wash them;
4. Replace the drip tray complete with grounds container;
5. Close the service door.

Cleaning the inside of the machine

Danger of electric shock!
14