Table of Contents
Advertisement
have the socket replaced with a suitable type by a qualified
professional.
Using the appliance for the first time
Please note :
•
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the mill. The machine is, however, guaranteed to be new.
•
You should customise water hardness as soon as possible
following the instructions in the section "Setting water
hardness" on page 15.
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 1).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When English appears, press the
seconds (fig. 2). Once the language has been saved, the
message "ENGLISH SET" is displayed.
Follow the instructions indicated by the appliance:
3. "FILL TANK": remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. "INSERT WATER SPOUT": Check that the hot water spout is
inserted on the nozzle and place a container with a minimum
capacity of 100 ml underneath (fig. 4).
5. "Hot water Confirm?": Press the
"PLEASE WAIT" is displayed and the appliance begins to
deliver water from the hot water spout.
The appliance ends the first start up procedure, then the
message "TURNING OFF, PLEASE WAIT" is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
Please note:
•
When using the appliance for the first time, you need to
make 4/5 cups of coffee or 4/5 cappuccinos before the
appliance starts to give satisfactory results.
TURNING THE APPLIANCE ON
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (fig. 1).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
•
To turn the appliance on, press the
The message "HEATING UP, PLEASE WAIT" is displayed.
After heating, the message "RINSING" is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message "READY
STANDARD TASTE" is displayed.
TURNING THE APPLIANCE OFF
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
To avoid damaging the appliance, always press the
to turn off.
button for a few
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
To turn the appliance off, press the
If the appliance is not used for an extended period, place the
main switch in the 0 position (fig. 6).
Never place the main switch in the 0 position while the
appliance is on.
button (fig. 2).
MENU SETTINGS
The following menu items can be selected: Clock, Start, Auto-
start, Descale, Temperature, Off after, Water hardness, Default
values.
To access the settings menu, press the MENU button. The light
on the button comes on.
Clock
To adjust the time on the display, proceed as follows:
1. Access the menu and press the
"CLOCK" is displayed;
2. Press the
the button down to change the time rapidly). When you
have finished, release the button. The time flashes.
3. Press the
4. Press the MENU button to exit the menu. The light on the
button goes off.
The time displayed when the machine is off (stand-by) is now
set.
Turning on
Once "AUTO-START Yes" has been enabled, the auto-start time
must be set as follows:
10
Important!
Danger of burns!
Please note:
button to change the time (hold
button to confirm;
button (fig. 5).
button
button (fig. 5).
button until
Advertisement
Table of Contents
Troubleshooting
