Fisher & Paykel WH1160HG1 Installation Manual
Hide thumbs
Also See for WH1160HG1:
- User manual (60 pages) ,
- Installation manual (19 pages) ,
- User manual (37 pages)
Related Manuals for Fisher & Paykel WH1160HG1
Summary of Contents for Fisher & Paykel WH1160HG1
- Page 1 FABRIC CARE SOLUTION STACKED INSTALLATION WH1160HG1, WH1160H1, DH9060HG1, DH9060H1, DH9060HLG1, DH9060HL1, FC1260HG1, FC1260H1, FM2060SG1 and FM2060S1 models INSTALLATION GUIDE NZ AU...
-
Page 2: Components Required
COMPONENTS REQUIRED TOOLS Supplied Not supplied 6mm Allen key Box cutter Spanner (washer) Phillips screwdriver Spanner (plinth) Level PARTS Supplied and required Supplied and to be discarded 4x M10 bolts 2x dryer front brackets 2x plinth bolt hole covers 2x dryer rear brackets 4x short stacking kit screws 2x dryer rear mounting screws 2x long stacking kit screws... - Page 3 ACCESSING YOUR PRODUCT SPECIFICATIONS For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit fisherpaykel.com/specify. Search by appliance type, product name or model code. 1920 1260 1900 1220...
-
Page 4: Prior To Installation
PRIOR TO INSTALLATION 1. Ensure cabinetry and servicing specifications have been met and clearances have been considered. Refer to the Planning Guide for details. fisherpaykel.com/specify 2. Ensure floor is level and clear and a finished return has been created. 3. Ensure power will remain accessible following install to allow access for any future product maintenance. - Page 5 UNPACK ALL PRODUCTS Washer and Dryer: Cut the straps and the line printed on the top of the carton. Lift to remove. Discard braces and corner posts. Remove any packaging and accessories from the drum and base packer. Dispose of packaging responsibly.
- Page 6 UNPACK ALL PRODUCTS Protect flooring before positioning products as close to the installation location as possible, ensuring enough working room is left available.
- Page 7 LEVEL PLINTH 1. Push the front of the plinth to open. Remove the divider before closing the drawer. 2. Place the plinth in its final install location. Adjust the feet using the supplied spanner until the washer is level front to back and corner to corner.
- Page 8 FIT WASHER TO PLINTH 1. Tilt the washer back onto a protected surface such as the plinth carton. Ensure cords and hoses are not crushed. For new products, we recommend keeping the transit bolts fitted during this step. 2. Unwind feet using the supplied spanner to remove.
- Page 9 FIT WASHER TO PLINTH 4. Using the spanner provided as a spacer, ensure a 4mm gap is left between the bolt head and the chassis. 5. Align all four brackets to the M10 bolts on the washer and slot into place. 6.
- Page 10 FIT WASHER TO PLINTH 7. Lift the washer upright, avoiding lifting from the lid. Take care as storage drawer may open. 8. Tighten the rear bolts.
- Page 11 REMOVE WASHER TRANSIT BOLTS 1. Using the supplied spanner, remove all four transit bolts from the back of the washer. 2. Pull the rubber grommets and spacers outwards to remove. 3. Using a Phillips screwdriver, remove the two side brackets.
- Page 12 REMOVE WASHER TRANSIT BOLTS 4. Remove and discard the braces. 5. Pull the two transit rods outwards to remove. Set aside for future use. 6. Cover the transit bolt holes using the supplied plugs.
- Page 13 INSTALL STACKING KIT TO WASHER 1. Align the front corner of the stacking kit to the washer. 2. Secure the stacking kit to the washer using the four supplied short screws in the marked locations. If using a drill, the lowest torque setting is recommended.
- Page 14 INSTALL DRYER TO STACKING KIT 1. Ensure stacking kit shelf is pushed all the way in and dryer feet have been fully wound in. 2. Lift dryer onto the stacking kit ensuring all four feet rest in the slots. 3. Using the two supplied long screws, secure the dryer to the stacking kit at the rear.
- Page 15 INSTALL DRYER TO STACKING KIT 4. Remove the two screws from the front of the dryer and refit through the stacking kit.
- Page 16 LEVEL PRODUCT SET 1. We recommend levelling and installing stacked products into alcove before fabric care cabinet. 2. Partially roll stacked products into alcove and check alignment. To do this, use the supplied 6mm hex key, rotate clockwise to lower both sets of wheels via the adjustment screws.
- Page 17 LEVEL PRODUCT SET 4. Using the supplied 6mm hex key, rotate counter-clockwise to raise both sets of wheels via the adjustment screws.
- Page 18 CONNECT CABLES AND HOSES 1. Refer to the Planning Guide for service information. fisherpaykel.com/specify 2. Optional: For displayed dryers, fit the drain hose extension if dryer can be plumbed. 3. Display-free models: Display-free models must be plumbed. Unwind the drain hose. Plumbed installations: Ensure hose can be connected to a drain.
- Page 19 CONNECT CABLES AND HOSES 4. Remove caps from washer and dryer before fitting one of the communication cables. Connect the washer and dryer via the communication cable. 5. Connect fabric care cabinet communication cable to dryer. 6. Connect the angled end of the cold water hose (supplied with washer) to the dryer.
- Page 20 CONNECT CABLES AND HOSES 7. Connect the angled end of the short hose (supplied with dryer) to the cold water inlet on the washer. 8. Connect both hoses to the top of the Y join supplied with the dryer. 9. Connect the straight hose to the bottom of the Y join.
- Page 21 CONNECT CABLES AND HOSES 10. Connect the angled end of hot hose to the orange outlet on the washer. If hot hose is not required, install a blanking cap. 11. Partially roll products into the alcove. Ensure fabric care cabinet communication cable is accessible from the rear of the dryer.
- Page 22 CONNECT CABLES AND HOSES 13. Install the drain hose guide to the back wall. Refer to the planning guide for placement details. 14A. Standpipe Installations: Route the drain hose through the guide and place into the standpipe. Ensure a maximum of 20mm of 20mm the hose rests in the standpipe.
- Page 23 CONNECT CABLES AND HOSES 15. Connect hoses to taps before turning on. Check for leaks at all connection points. 16. Connect the power cables and check products are powered on and are connected. 17. Roll products into the alcove. Take care not to damage hoses or cords.
- Page 24 CONNECT CABLES AND HOSES 18. Turn the adjustment screw counter-clockwise to retract the wheels. Ensure the wheels are fully raised off the floor. Floor 19. Check alignment and ensure required clearances are maintained. Adjust as required. 20. Once adjustment is complete, fit the plinth bolt hole covers.
- Page 25 INSTALL FABRIC CARE CABINET 1. Open the cabinet door and lower the rear wheel using the supplied Allen key. Rotate clockwise to lower the wheel and counter-clockwise to raise. 2. When adjusting the wheel, ensure front of the door doesn’t damage the floor. 3.
- Page 26 INSTALL FABRIC CARE CABINET 4. Tighten the locking nuts up to the base of the cabinet to lock feet in position. 5. Lower the rear wheel to achieve clearance between rear feet and floor. When adjusting the wheel, ensure front of the door doesn’t damage the floor.
- Page 27 INSTALL FABRIC CARE CABINET 7. Push cabinet into cavity taking care not to damage cords. Rotate the rear wheel adjustment screw anti- clockwise to place the full cabinet weight onto feet. Ensure rear corners are level and set to the desired height. 8.
- Page 28 INSTALL FABRIC CARE CABINET 9. Ensure cabinet is resting on all four feet and all wheels have been raised. 10. Check final alignment and ensure required clearances are maintained. Adjust as required. 11. Clip drip tray into position.
-
Page 29: Installer Checklist
INSTALLER CHECKLIST Complete and keep for safe reference: Model Serial no. Purchase date Purchaser Dealer address Installer’s name Installer’s signature Installation company Installation date... - Page 30 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.