Related Manuals for TCS SuperSTAT SZ1053
Summary of Contents for TCS SuperSTAT SZ1053
- Page 1 CONFIGURATION GUIDE Communicating Thermostat SuperSTAT SZ1053 2800 Laura Lane • Middleton, WI 53562 800.288.9383 www.tcsbasys.com 202308...
-
Page 2: Table Of Contents
Contents Introduction ............................3 Display Screen and Keypad ........................3 Locating the Programming Keypad .........................3 Programming Keypad Access .........................4 Navigating Via Keypad ..........................4 Program Setup Mode ..........................5 Basic Setup ..............................5 System Mode ..................................5 Occupancy Settings ................................ 6 Heat/Cool Digital Outputs ............................. 7 Time Clock .................................. -
Page 3: Introduction
“Programming Keypad Access” on page If you have any questions regarding your SuperSTAT, do not hesitate to contact TCS Technical Support at 800.288.9383, ext. 2. Our Technical Support Department hours are Monday – Friday, 7:00 a.m. to 7:00 p.m. (CST). -
Page 4: Programming Keypad Access
R W/Y1 W/Y2 G A02 A01 Configuration – DI3 OVR T1 Programming Keypad Access The keypad can be configured to restrict access to the Programming Setup and Clock and Schedule functions. You can control the access to either function by configuring the keypad dip switches on the inside of the front cover as shown. Keypad Dip Switch Settings 1 2 3 4 5 The dip switch panel controls access to clock,... -
Page 5: Program Setup Mode
Configuration Program Setup Mode Before entering PROGRAM SETUP Mode, ensure that the temperature sensor dip switch settings match your intended use (see the SZ1051/1053 SuperSTAT Installation Manual). If the dip switch settings do not match the configuration settings in this section, the SuperSTAT will not function properly. NOTE: PROGRAM SETUP Mode can be disabled via dip switch settings (see “Programming Keypad Access”... -
Page 6: Occupancy Settings
Configuration Occupancy Settings STEP 1 Occupied Fan Mode: Choose between ON (continuous), SET OCCUPIED FAN COOL (gas heat or no heat), or AUTO for fan run times during occupied periods. MODE: AUTO STEP 2 Unoccupied Fan Mode: Choose between AUTO or COOL for SET UNOCCUPIED fan run times during unoccupied periods. -
Page 7: Heat/Cool Digital Outputs
Configuration STEP 11 Occupied Cool Setpoint D: Set the cooling setpoint for this OCCUPIED COOL occupied period. SETPOINT D: STEP 12 Unoccupied Cool Setpoint: Set the Unoccupied Mode’s UNOCCUPIED COOL cooling setpoint. SETPOINT: STEP 13 User Setpoint Limit: Enter the amount a user is allowed the LIMIT SETPOINT to adjust the preset occupied setpoints ADJUST +/-... -
Page 8: Time Clock
Configuration Time Clock STEP 1 Time Clock Output: Select whether the auxiliary output will be TIME CLOCK OUTPUT OPEN during occupied periods and closed during unoccupied periods, or CLOSED during occupied periods and open during OCCUPIED = OPEN unoccupied periods. Modulating Outputs STEP 1 Output 1 Proportional Band: Enter the number of degrees... - Page 9 Configuration STEP 10 Output 2 Unoccupied Action: Select whether the unoccupied MOD OUT 2 UNOCC action will be 0mA, 4mA, 20mA, or modulating. ACTION: STEP 11 Discharge Air Sensor: Select whether to use a discharge air ENABLE DISCHARGE sensor. To monitor only, select NO. NOTE: Refer to the SZ1051/1053 SuperSTAT Installation...
-
Page 10: Digital Inputs
Configuration STEP 21 Outdoor Air Sensor Function: Select whether you are using ENABLE OUTDOOR an outdoor air sensor. To monitor only, select NO. NOTE: Refer to the SZ1051/1053 SuperSTAT Installation AIR FUNCT? Manual for dip switch settings, which must also be set STEP 22 Cooling Lockout: Enter an outdoor air cooling lockout COOLING LOCKOUT temperature. -
Page 11: Keypad Access Code
Configuration Keypad Access Code STEP 1 Programming Access: Select whether an access code is REQUIRE CODE FOR required to access Programming Setup. NOTE: Use dip switch settings to lock out access completely PROGRAMMING? (see ““Programming Keypad Access” on page STEP 2 Clock and Schedule Access: Select whether an access code REQUIRE CODE FOR is required to access the Clock and Schedule menus. -
Page 12: Occupancy Schedules
Configuration Occupancy Schedules STEP 1 Set Occupancy Time Periods: This screen indicates that the SET OCCUPIED day of the week shown is ready for configuring up to four occupancy time periods. Press the CLOCK SETUP button on TIMES MONDAY: the keypad to advance to the setup screens for the day shown. STEP 2 Occupancy Time Periods (1 of 2): Set hours and minutes A:08:00 TO 17:00... -
Page 13: Daylight Saving
Configuration STEP 3 Set Occupied Times Holiday No. 2: This screen indicates that SET OCCUPIED the occupancy times for second holiday group are ready to be configured. Press the CLOCK SETUP button on the keypad TIMES HOLIDAY #2 to advance to the setup screens for the holiday group. STEP 4 Occupancy Time Periods (1 of 2): Holiday 2 does not give A:08:00 TO 17:00...