Jam Code; Jam Codes (Main Body); Jam Codes (Adf) - Canon ImageRUNNER 1022iF Service Manual

Chapter 14
Display Detail Code
Code
E730 0000
E733 0000
E736 0000
E739 0000
E805 0000
E808 0000

14.2 Jam Code

14.2.1 Jam Codes (Main body)

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Code Name
0104 Pickup Delay Jam
0208 Pickup Stationary Jam
010c Delivery Sensor Delay Jam
0210 Delivery Sensor Stationary
Jam
0214 Stationary jam in machine
021c Wound Paper Jam at Fuser
1118 Door open jam

14.2.2 Jam Codes (ADF)

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Code Name
0000 Unknown jam
0007 Initial stationary
0008 Document edge sensor
delay jam
0009 Document edge sensor
stationary jam
000a Paper absence (Pull out
the document.)
000c Delivery delay jam
000d Delivery stationary jam
0010 Pickup NG
14-2
Main Cause/Symptom
inside error of the image processor PCB (PDL system error)
The inside of the image processor PCB is faulty.
Erroneous communication between controller and printer
Cannot communicate with the printer at startup.
CCU communication error
The installed modem PCB is incompatible.
Erroneous communication between controller and network board
The installed network board is incompatible.
Fan failure
The fan is faulty.
Fixing drive circuit failure
- The heater does not turn on.
- A fixing drive motor failure was detected.
Sensor No.
SR11 After execution of a pickup retry, the registration sensor (SR11) does not detect the leading edge of
paper within a specific period of time. Or after the duplex drive solenoid (SL1) is on, the registration
sensor (SR11) does not detect the leading edge of paper within a specific period of time.
SR11 After the registration sensor (SR11) has detected the leading edge of paper, the registration sensor
(SR11) does not detect the trailing edge of paper within a specific period of time.
SR5 After the registration sensor (SR11) has detected the leading edge of paper, the delivery sensor
(SR5) does not detect the leading edge of paper within a specific period of time.
SR5 - The delivery sensor cannot detect absence of paper within the specified time after turning off of
the registration clutch.
- The delivery sensor cannot detect absence of paper within the specified time after the sensor
detected the leading edge of paper.
SR5, SR9 After the registration sensor (SR11) has detected the trailing edge of paper, the delivery sensor
(SR5) does not detect the trailing edge of paper within a specific period of time.
SR5, SR11 The delivery sensor (SR5) has detected absence of paper within the prescribed time after it detected
presence of paper.
SR5, SR9, SR11, The door was opened when there was printing paper in the transport path.
SW2
Sensor No.
-
SR2002, SR2003, SR2004
SR2002
SR2002
SR2001
SR2002
SR2002
SR2003
Countermeasure
- Replace the image processor PCB.
- Check the connectors of the DC controller PCB and image
processor PCB for normal connection.
- Check the power supply of the printer (Check whether
initialization is performed at startup).
- Replace the DC controller PCB or image processor PCB.
- Check the connectors of the image processor PCB and modem.
- Replace the modem PCB.
- Replace the image processor PCB.
- Check the connectors of the image processor PCB and LAN
PCB for normal connection.
- Replace the LAN PCB.
- Replace the image processor PCB.
- Check the fan connector.
- Replace the fan.
- Replace the DC controller PCB.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the fixing drive motor.
- Replace the DC controller PCB.
- Replace the power supply PCB.
T-14-2
Description
T-14-3
Description
Other errors
Paper is detected in the transport path before the ADF starts initial
operation.
The document edge sensor does not detect paper when the paper has been fed by the
predetermined distance since reception of a pickup request.
The trailing edge of paper is not detected when the paper has been fed by the
predetermined distance since detection of it by the document edge sensor.
The Document set sensor has been held off since start of pickup.
In case the internal software signal "Delivery Sensor OFF" set in the system cannot
be detected, when the leading edge of paper is detected by the document edge sensor
and fed the prescribed distance, and after the paper's trailing edge is detected.
In case the internal software signal "Delivery Sensor ON" set in the system cannot
be detected, when the paper feed request is received and the paper is fed the
prescribed distance, and the leading edge of paper is detected and paper is fed the
prescribed distance .
The registration sensor has been held off since paper pickup started.
0013-1433
0013-1435