Canon ImageRUNNER 1022iF Service Manual page 204

Contents
15.4.4 <No.007 ATT transmission level> ........................................................................................................................................ 15-13
15.4.5 <No.008 V.34 modulation speed upper limit> ...................................................................................................................... 15-13
15.4.6 <No.009 V.34 data speed upper limit>.................................................................................................................................. 15-13
15.4.7 <No.010 Frequency of the pseudo CI signal> ....................................................................................................................... 15-13
15.5 Setting of Numeric Parameter (NUMERIC Param.)............................................................................................... 15-13
15.5.1 Numerical Parameter Composition........................................................................................................................................ 15-13
15.5.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>. 15-14
15.5.3 <005: NCC pause length (pre-ID code)>............................................................................................................................... 15-14
15.5.4 <006: NCC pause length (post-ID code)> ............................................................................................................................. 15-14
15.5.5 <010: line connection identification length> ......................................................................................................................... 15-14
15.5.6 <011: T.30 T1 timer (for reception)> .................................................................................................................................... 15-14
15.5.7 <013: T.30 EOL timer> ......................................................................................................................................................... 15-14
15.5.8 <015: hooking detection time> .............................................................................................................................................. 15-14
15.5.9 <016: time length to first response at time of fax/tel switchover> ........................................................................................ 15-14
15.5.10 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019: pseudo
RBT signal pattern OFF time length (long)> ............................................................................................................................... 15-14
15.5.11 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022: pseudo CI
signal pattern OFF time length (long)> ........................................................................................................................................ 15-15
15.5.12 <023: CNG detention level for fax/tel switchover> ............................................................................................................ 15-15
15.5.13 <024: pseudo RBT transmission level at time of fax/tel switchover>................................................................................. 15-15
15.5.14 <025: Answering machine connection function signal detection time>.............................................................................. 15-15
15.5.15 <027: V.21 low-speed flag preamble identification length> ............................................................................................... 15-15
15.5.16 <056 - 061: Count type select >........................................................................................................................................... 15-15
15.6 Setting of Scanner Functions (SCANNER) ............................................................................................................ 15-18
15.6.1 Numeric Parameter Functional configuration........................................................................................................................ 15-18
15.6.2 <024:CIS scan position during ADF scanning> .................................................................................................................... 15-19
15.6.3 <026:Distance from the standby position of CIS to the shading start point>........................................................................ 15-19
15.6.4 <031: Vertical scan start position adjustment>...................................................................................................................... 15-19
15.6.5 <032: Horizontal scan start position adjustment> ................................................................................................................. 15-19
15.6.6 <033: Vertical scan magnification correction> ..................................................................................................................... 15-19
15.6.7 <034: Horizontal scan magnification correction> ................................................................................................................. 15-19
15.6.8 <035: - 036:Reader motor speed change> ............................................................................................................................. 15-19
15.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>.......................................... 15-19
15.6.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)> ................................... 15-19
15.6.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)>........................................................................ 15-20
15.6.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)> .................................................................. 15-20
15.6.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>........................................................................... 15-20
15.6.14 <046: Horizontal scan end position correction (standard:scanning on ADF)> ................................................................... 15-20
15.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)> ....................................... 15-20
15.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)> ................................... 15-20
15.6.17 <054: Pickup motor speed correction (when the ADF is used) >........................................................................................ 15-20
15.6.18 <193: ADF special standard-sized paper: LGL misidentification-ready>........................................................................... 15-20
15.6.19 <194: ADF special standard-sized paper: LTR misidentification-ready>........................................................................... 15-20
15.6.20 <195: ADF special standard-sized paper: LTR_R misidentification-ready> ...................................................................... 15-20
15.6.21 <213: XYZ correction value (X) of standard white plate> (equipped with SEND functions) ............................................ 15-21
15.6.22 <214: XYZ correction value (Y) of standard white plate> (equipped with SEND functions) ............................................ 15-21
15.6.23 <215: XYZ correction value (Z) of standard white plate> (equipped with SEND functions) ............................................ 15-21
15.7 Setting of Printer Functions (PRINTER) ................................................................................................................ 15-21
15.7.1 Service Soft Switch Settings (PRINTER).............................................................................................................................. 15-21
15.7.1.1 SSSW-SW05............................................................................................................................................................................................. 15-21
15.7.1.1.1 List of Functions ............................................................................................................................................................................... 15-21
15.7.1.1.2 Detailed Discussions of Bit 7............................................................................................................................................................ 15-21
15.7.1.2 SSSW-SW14............................................................................................................................................................................................. 15-22
15.7.1.2.1 List of Functions ............................................................................................................................................................................... 15-22
15.7.1.2.2 Detailed Discussions of Bit 0............................................................................................................................................................ 15-22
15.7.1.2.3 Detailed Discussions of Bit 2............................................................................................................................................................ 15-22
15.7.1.2.4 Detailed Discussions of Bit 4............................................................................................................................................................ 15-22