Bosch Professional GBM 10 RE Original Instructions Manual page 11

likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is suitable for drilling in wood, metal, ceramic
and plastic. Power tools with electronic control and clock-
Bosch Power Tools
wise/anti-clockwise rotation are also suitable for screwdriv-
ing and thread cutting.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Front sleeve
(3) Rear sleeve
(4) Belt clip
(5) Lock-on button for on/off switch
(6) On/off switch
(7) Rotational direction switch
(8) Handle (insulated gripping surface)
a)
(9) Screwdriver bit
a)
(10) Universal bit holder
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Rotary Drill
Article number
Rated power input
Max. power output
No-load speed
Rated speed
Rated torque
Spindle collar diameter
Speed control
Clockwise/anti-clockwise ro-
tation
Max. drilling diameter
– Steel
– Wood
– Aluminium
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power level
94 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
English | 11
GBM 10 RE
3 601 D73 6..
W 600
W 360
-1
min 0–2 600
-1
min 1 676
Nm 20
mm 43
●
●
mm 10
mm 25
mm 10
mm 1–10
kg 1.7
/ II
1 609 92A 7YC | (04.07.2022)