Figures - IBM 2073-700 Quick Installation Manual

Figures

1. This figure shows 12 drives and two end caps
(model 2076-112). .
2. This figure shows 24 drives and two end caps
(model 2076-124). .
3. Rear view of a model 2076-112 or a model
2076-124 control enclosure .
4. This figure shows the data ports in the rear of
the control enclosure..
5. 10 Gbps Ethernet ports on the rear of the
Storwize V7000 enclosure .
6. Rear view of a model 2076-212 or a model
2076-224 expansion enclosure .
7. SAS ports and LEDs in rear of expansion
enclosure. . . .
8. Front view of file module .
9. Rear view of file module
10. Recommended rack locations.
11. Hole locations in the front of the rack .
12. Hole locations in the back of the rack .
13. Removing the enclosure end cap
14. Securing an enclosure to a rack cabinet
15. Cable management arm box contents. .
16. Friction rail box contents. .
17. Locate a 2U space in the lower section of the
rack. . . . . .
18. Open the rear slide rail hooks. .
19. Install the rear end of the slide rails. .
20. Install the front end of the slide rails. .
21. Install the front end of the slide rails. .
22. Install the file module on the slide rails.
23. Slide the file module into the rack. .
24. Install the cable management support arm. The
graphic shows the rear of the rack..
© Copyright IBM Corp. 2011
. . . . . . . . .
. . . . . . . . .
. . . . . .
. . . . . . . .
. . . . . .
. . . . .
. . . . . . . . .
. . . . . .
. . . . . . .
. . . . .
. .
. .
. . . .
. .
. . . . . .
. . . . . . . . .
. . . .
. .
. .
. .
. . .
. . .
25. Install the cable management arm. .
. 4 26. Adjust the location of the cable management
arm. . .
. 4 27. Connect and route the cables.
28. Secure the cable management arm and the file
. 5 module in the rack for shipping if needed. .
29. Install the front screws.
. 5 30. Internal cables. This is a logical diagram of the
connectivity and does not reflect the exact
. 6 physical system. .
31. Attaching an expansion enclosure to the
. 7 control enclosure .
32. Adding a second expansion enclosure.
. 7 33. Attaching SAS cables to the enclosures
. 8 34. Control enclosure Ethernet network
. 9 connections. This diagram is conceptual, not a
. 11 physical representation.
. 13 35. File module node Ethernet network
. 14 connections. This is a logical diagram of the
. 15 connectivity and does not reflect the exact
16 physical system. .
. 17 36. Diagram showing how to connect the file
. 18 modules to the control enclosure using Fibre
Channel cables. Refer to previous table. .
. 18 37. Sliding the cable retention bracket directly
. 19 behind the power cord .
. 19 38. 24 drives and two end caps .
. 20 39. 12 drives and two end caps .
. 20 40. LEDs on the power supply units of the
21 expansion enclosure.
. 21 41. LEDs on the power supply units of the control
enclosure .
. 22 42. Initialization tool welcome panel .
. . . . . . . . .
. .
. . . .
. . . . . .
. . . . . .
. . . .
. . . . . .
. . . .
. .
. .
. . . . .
. . . . . . . .
. . . . 22
. . . . 23
. . . . 23
. 24
. . . . 24
. . . . 26
. . . . 27
. . . 28
29
. . . . 30
. . . . 30
. . 33
. . . . 35
. . . . 36
. . . . 36
. . . . 37
. . . . 38
. . . . 44
v