Roland Sound Canvas SC-8850 Owner's Manual page 121

Effects that connect two types of effect in
parallel (parallel 2)
Effect types in which two different effects are connected in
parallel allow you to apply different effects to L and R
independently. By using parallel effects for the sound of two
Parts, you can achieve a result as if two separate effect units
were used.
For example, you might select a guitar sound for Part 1 and
an organ sound for Part 2. Then set the pan setting to L63 (far
left) for Part 1, and to R63 (far right) for Part 2. Apply the
effect 60: OD/Rotary to both Parts 1 and 2. By then making
appropriate settings for the OD Pan and RT Pan effect
parameters, you can apply Overdrive to the guitar sound
and Rotary to the organ sound, effectively allowing you to
use two separate effects at once.
fig.9-60
Part 01 L63
028 Clean Gt.
Overdrive/
Distortion
L
Part 02 R63
017 Organ 1
Rotary
R
56: Cho/Delay (Chorus/Delay)
This effect connects a chorus and a delay in parallel.
fig.9-61
L
Chorus
Delay
R
Cho Dly (Chorus Pre Delay)
Adjusts the time delay from when the direct sound begins
until the chorus sound is heard.
Cho Rate (Chorus Rate)
Adjusts the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
Adjusts the modulation depth of the chorus effect.
+Cho Bal (Chorus Balance)
Adjusts the volume balance between the direct and the
chorus sound.
"D" or "E" on the display respectively means D (direct
sound) or E (effect sound) values of 100.
Cho Pan (Chorus Output Pan)L63–0–R63 [16 (40 03 12)]
Adjusts the stereo position of the chorus sound. L63 is far
left, 0 is center, and R63 is far right.
Cho Level (Chorus Level)
Adjusts the volume of the chorus sound.
60 OD/Rotary
Pan
Pan
[11H, 00H]
Pan
Balance
Pan
0–100ms [1 (40 03 03)]
0.05–10.0 [2 (40 03 04)]
0–127 [3 (40 03 05)]
D>0E–D0<E [5 (40 03 07)]
0–127 [17 (40 03 13)]
Dly Time (Delay Time)
Adjusts the time delay from when the direct sound begins
until the delay sound is heard.
Dly Fb (Delay Feedback Level) -98%–+98% [7 (40 03 09)]
Adjusts the proportion (%) of the delay sound that is fed
back into the delay input. Negative (-) settings will invert
the phase.
Dly HF (Delay HF Damp)
Adjusts the frequency above which delayed sound fed back
to the delay input will be cut. If you do not wish to cut the
high frequencies of the feedback, set this parameter to
Bypass.
#Dly Bal (Delay Balance)
Adjusts the volume balance between the direct and the
delay sound.
"D" or "E" on the display respectively means D (direct
sound) or E (effect sound) values of 100.
Dly Pan (Delay Output Pan)
Adjusts the stereo position of the delay sound. L63 is far
left, 0 is center, and R63 is far right.
Dly Level (Delay Level)
Adjusts the volume of the delay sound.
Level (Output Level)
Adjusts the output level.
Using Insertion Effects
0–500ms [6 (40 03 08)]
315–8k/Bypass [8 (40 03 0A)]
D>0E–D0<E [10 (40 03 0C)]
L63–0–R63 [18 (40 03 14)]
0–127 [19 (40 03 15)]
0–127 [20 (40 03 16)]
121