Volvo Penta TAD1170VE Operator's Manual
  1. Manuals
  2. Brands
  3. Volvo Penta Manuals
  4. Engine
  5. TAD1170VE
  6. Operator's manual

Volvo Penta TAD1170VE Operator's Manual

11l
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operator's manual
11L
TAD1170VE, TAD1171VE, TAD1172VE

Advertisement

Table of Contents
loading

Related Manuals for Volvo Penta TAD1170VE

Summary of Contents for Volvo Penta TAD1170VE

  • Page 1 Operator’s manual TAD1170VE, TAD1171VE, TAD1172VE...
  • Page 2 WARNING! Operating, servicing and maintaining an engine can expose you chemi- cals including engine exhaust, carbon monoxide, phthalates, and lead which are known to the State of California to cause cancer and birth defects or other reproductive harm. Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

  • Page 3: Table Of Contents

    Maintenance and replacement parts ............15 Excessive strain on a product and components ........15 Environmental care ................. 16 Emission Aftertreatment System ............. 18 Volvo Penta Dealer Network ..............18 Volvo Penta Action Service ..............19 Presentation ....................20 Engines ....................20 EMS (Engine Management System) ............
  • Page 4 Lubrication System ................85 Fuel System ................... 86 Cooling System ..................88 Coolant, Mixing ..................88 Water Quality ..................89 Inlet and Exhaust System ..............89 Electrical System .................. 89 Identification Numbers ................. 90 Index ......................93 47710925 01-2019 © AB VOLVO PENTA...

  • Page 5: Foreword

    Pay careful attention to the safety instructions included in the manual. As the owner of a Volvo Penta engine, you become part of a worldwide network of dealers and service workshop that assist you with technical advice, service requirements and replacement parts.

  • Page 6: Safety Information

    This chapter describes how safety precautions are If anything remains unclear or if you are unsure of presented in the manual and on the product. Read the something, contact your Volvo Penta dealer for chapter through very carefully before you start the assistance.
  • Page 7 WARNING! Ensure that all machine guards and safety devices are in place and are functional. P0024482 CAUTION! Never use tools or products that show signs of damage. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 8 Ensure that the workplace is well ventilated and take the necessary precautions before welding or grinding begins. Always ensure that there is a fire extinguisher close at hand in the work area. P0024470 47710925 01-2019 © AB VOLVO PENTA...
  • Page 9 Spare parts — safety WARNING! Always use spare parts with the same quality as genuine Volvo Penta parts to minimize the risk of an explosion or fire. Components in fuel systems and electrical systems on Volvo Penta engines are designed and manufactured to minimize the risk of explosions and fire, in accordance with applicable legal requirements.
  • Page 10 Prohibition on use of start spray WARNING! Never use start spray or similar agents to start an engine. This may cause an explosion in the inlet manifold. Risk of personal injury. P0024483 47710925 01-2019 © AB VOLVO PENTA...
  • Page 11 Before any work on the cooling system WARNING! Stop the engine and let it cool before starting work on the cooling system. Hot fluids and hot surfaces can cause burns. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 12 Smoking is forbidden and the engine must be stopped. Proper fuel quality IMPORTANT: Always use the fuel recommended by Volvo Penta. See Technical Data in Operator’s Manual. Other fuel can damage the engine. Wrong fuel quality can also lead to higher service costs.
  • Page 13 If it comes electrolyte to unprotected skin, wash immediately with soap and water. Layout of the battery compartment IMPORTANT: Make sure the battery compartment is designed according to current safety standards. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 14 Cleanliness for sensitive components IMPORTANT: Observe meticulous cleanliness when handling system components. Even minimal amounts of dirt could cause a breakdown. Adjustment of the clutch CAUTION! Clutch adjustments must be carried out with the engine stopped. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 15: Introduction

    Warranty Your new Volvo Penta engine is covered by a limited warranty, subject to the conditions compiled in the Warranty Information. AB Volvo Penta’s liability is limited to the specification in the Warranty Information and Emission Control System Warranty Statement.

  • Page 16: Fuel, Oils And Coolant

    Make sure to always use suitable and correctly mixed coolant. Future warranty claims related to engine and accessories may be denied if an unsuitable coolant has been used, or if the instructions for coolant mixture have not been followed. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 17: Maintenance And Replacement Parts

    These qualities will be maintained through regular servicing and the use of spare parts with the same quality as genuine Volvo Penta parts. If reliable and purpose-built parts are not used, your safety, health, and the machine’s function may be compromised.

  • Page 18: Environmental Care

    Introduction Environmental care Environmental care is a core value at Volvo Penta. Energy efficiency and low emissions are among the most important product related aspects and priority focus areas for Volvo Penta business. Several of the global challenges the world faces are directly or indirectly related to power industries and transports.
  • Page 19 NOTICE! Neglects or failure to follow the points listed here may invalidate the engine emission certificate. This means AB Volvo Penta can no longer guarantee engine conformity with the certified model. Volvo Penta is not responsible for damages or costs arising as a result of this.

  • Page 20: Emission Aftertreatment System

    The Volvo Penta global network of authorized dealers is at your service. We strongly recommend that you take your product to an authorized Volvo Penta dealer for service and repair. They are specialists in Volvo Penta products and have the accessories, genuine...

  • Page 21: Volvo Penta Action Service

    Introduction Volvo Penta Action Service Our global dealer network, your first line of contact, is backed up by Volvo Penta Action Service, a phone based breakdown and support service providing assistance 24 hours a day, every day of the year.

  • Page 22: Presentation

    (EMS), turbocharger, charge air cooler, a thermostatically controlled cooling system and electronic speed control. In order to reduce emission levels the engines are equipped with EATS (Exhaust Aftertreatment System) and EGR (Exhaust Gas Recirculation). 47710925 01-2019 © AB VOLVO PENTA...

  • Page 23: Ems (Engine Management System)

    EMS is an electronic system with CAN communication (Controller Area Network) for diesel engine control. The system has been developed by Volvo Penta and includes fuel regulation and diagnostic functions. The system consists of a control unit, injectors, a number of sensors that supply the control unit with information, and connectors for diagnostics and functional checks.

  • Page 24: Eats (Exhaust Aftertreatment System)

    Should the system detect deviations, the maximum engine torque and engine speed will be reduced and a fault code stored in the control unit. For further information refer to EATS Inducements, page 50. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 25 CAUTION! The EATS system needs time to for automatically drainage and depressurizing. Wait at least two minutes after the engine been turned off before removing the AdBlue/DEF hoses. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 26: Overview

    Presentation Overview The system comprises: 1 Tank 2 Pump 3 Injector 4 EATS Catalyst and Muffler 5 Catalytic Converter The atomized AdBlue®/DEF is sprayed into the exhaust gases upstream of the catalytic converter. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 27 EATS system, as the remaining solution will circulate and cool the system. However, emissions from the engine will increase as the injection valve is closed and no exhaust aftertreatment will take place. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 28: Operation

    Do not try to clean with water or compressed air. AdBlue®/DEF is not a combustible product. When exposed to high temperatures it will convert to ammonia and carbon dioxide. However, do not allow 47710925 01-2019 © AB VOLVO PENTA...
  • Page 29 IMPORTANT: AdBlue®/DEF spillages may not be washed into drains. If a spill should occur, the solution must be absorbed using dry sand or other non-flammable material and handled according to local and national regulations. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 30 — flush with copious amounts of water and remove contaminated clothing. • eye contact — flush thoroughly for several minutes; contact physician as necessary. • inhalation — breathe fresh air and contact physician as necessary. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 31: Instruments And Controls

    Instruments and Controls Control Interface Module The Volvo Penta Control Interface Module (CIM) instrument panel communicates with the engines control unit and has a number of functions as control, monitoring and diagnostics. NOTICE! Settings and the type of engine data presented on the display may vary depending on the installation and engine model.
  • Page 32 . • WARNING (WARNING), yellow text, the system has detected a fault — Volvo Penta recommends to contact a qualified workshop as soon as possible. • MESSAGE (MESSAGE), blue text, non-critical engine message for the operator.
  • Page 33 . This will also provied information about number of engine hours when the fault became active and the SPN and FMI codes. P0028065 47710925 01-2019 © AB VOLVO PENTA...
  • Page 34 • Engine Hardware ID (Engine Hardware ID) • CIM hardware ID (CIM hardware ID) • Engine Software ID (Engine Software ID) • CIM Software ID (CIM Software ID) • Chassis ID (Chassis ID) P0028160 47710925 01-2019 © AB VOLVO PENTA...

  • Page 35: Display Control Unit

    Instruments and Controls Display Control Unit The Volvo Penta DCU II instrument panel communicates with the engines control unit and has a number of functions as control, monitoring and diagnostics. NOTICE! Settings and the type of engine data presented on the display may vary depending on the installation and engine model.
  • Page 36 . • VARNING (WARNING), yellow text, the system has detected a fault — Volvo Penta recommends to contact a qualified workshop as soon as possible. • MEDDELANDE (MESSAGE), blue text, non-critical engine message for the operator.
  • Page 37 Brightness). Sets backlighting in the display instrument. • Change background color (Change background color). Select background color, gray or white. Language (Language) Sets the display language; chooses between English, French, German, Spanish and Chinese. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 38 NOTICE! The settings in the following menus do not normally need to be changed; should a change be necessary it must be carried out by an authorized Volvo Penta technician. Refer to the installation manual for further engine information. Authorized Volvo Penta dealer or OEM only •...

  • Page 39: Starting

    Never break the circuit with the main switch while the engine is running. Alternator and electronics could be damaged. • Move the engine speed control to idle, and open the disengageable clutch/gearbox if installed. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 40: Starting The Engine

    Make sure the cooling system is filled with a coolant mixture. Refer to Maintenance, page 68. • The batteries must be in good condition. Cold weather reduces battery capacity. Increased battery capacity may be necessary. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 41: Never Use Start Spray

    Risk of arcing. Do not bend over any of the batteries either. 4 Remove the cables in the reverse order. IMPORTANT: The ordinary cables to the standard batteries must not under any circumstances be loosened. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 42: Operation

    The consequences can be carbon build-up on valves, piston crowns and the exhaust turbine, which could affect engine performance. Both conditions can lead to increased oil consumption and eventually external oil leakage from joints in the 47710925 01-2019 © AB VOLVO PENTA...
  • Page 43 • If visible slobber has occurred, it can be burned off by running the engine on at least 30% load for about 40-60 minutes. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 44: Engine Shutdown

    P0018811 Auxiliary Stop For location of the extra stop, refer to Maintenance, page 56. WARNING! Working with or approaching a running engine is a safety risk. Watch out for rotating components and hot surfaces. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 45: After Engine Shutdown

    If there is a risk of freezing, the coolant in the cooling system must have adequate antifreeze protection. Refer to Maintenance, page 68. IMPORTANT: A poorly charged battery can freeze and burst. Refer to Battery, page 80. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 46: Fault Handling

    The operator is warned that there is a malfunction via the instruments. Depending on the instrumentation in use, the fault message is shown in various ways. Fault codes can also be read out by the Volvo Penta diagnostic tool. Depending on the severity of the fault, the diagnostic function will take various actions to protect the engine and limit emissions (e.g.

  • Page 47: Dcu Ii (Display Control Unit)

    If so a new fault codes is registered. If a malfunction has not been corrected it will be registered once again and has to be acknowledged again. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 48: Fault Tracing

    A number of symptoms and possible causes of engine malfunctions are described in the table below. Always contact your Volvo Penta dealer if any problems occur which you cannot solve by yourself. NOTICE! Read through the safety advice for care and maintenance work in the chapter Safety precautions for maintenance and service operations before you start work.
  • Page 49 18 Faulty circulating pump 19 Defective thermostat 20 Blocked charge air cooler 21 Oil level too high 22 Alternator drive belt slips 23 High back pressure in the exhaust system 24 Break in ”Pot+” cable to throttle 47710925 01-2019 © AB VOLVO PENTA...

  • Page 50: Eats Warnings And Inducements

    EATS Inducements, page 50. NOTICE! Warning messages and symbols may vary depending on the installation; shown here are those seen on panels sold by Volvo Penta. Warning Symbols Stimulus for power reduction warning. A fault has been detected in the EATS system.

  • Page 51: Quality Shortcomings And Component Defects

    • that the EGR valve is not stuck. If the fault can not be remedied with any of the above, refer to EATS Inducements, page 50. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 52: Eats Inducements

    75% power. Each 10-minute period requires a manual activation. 7 If an additional fault recurs within 40 hours after the first fault was remedied, available running time will be reduced to 30 minutes from the moment the fault is detected. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 53: Fault Code Register

    Fuel Injector, Cylinder #1 3, 5 Fuel Injector, Cylinder #2 3, 5 Fuel Injector, Cylinder #3 3, 5 Fuel Injector, Cylinder #4 3, 5 Fuel Injector, Cylinder #5 3, 5 Fuel Injector, Cylinder #6 47710925 01-2019 © AB VOLVO PENTA...
  • Page 54 Aftertreatment Reagent Pump Motor Speed 4375 0, 1, 3, 4, 5, 12, Aftertreatment Reagent Pump Control 4376 3, 4, 5, 7 Aftertreatment Reagent Direction Valve 5016 ACM Actuator Supply Voltage #4 5392 Aftertreatment Reagent Pump Control 47710925 01-2019 © AB VOLVO PENTA...
  • Page 55 3, 4, 5 EGR "A" / Volvo Compression Brake (VCB) Control Circuit 520690 3, 5 EGR "A" Control / Turbocharger/Supercharger Wastegate Solenoid "A" 520691 Torque Speed Control 1 Received With Errors (Counter or Checksum) 47710925 01-2019 © AB VOLVO PENTA...

  • Page 56: Maintenance Schedule

    Maintenance Schedule Your Volvo Penta engine and its equipment are designed for high reliability and long life. The engines are built to have the smallest possible environmental impact. If given preventive maintenance, according to the maintenance schedule, these qualities will be retained and unnecessary malfunctions will be avoided. In order for the warranty to be valid, the owner must make sure that the services in the service intervals are performed.

  • Page 57: Maintenance

    Make it impossible to start the engine by removing the start key and cutting the system voltage with the main switches. When ordering service or spare parts, always specify the engine and transmission identification number. Refer to Technical Data, page 90. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 58: Orientation

    1 Starter motor 2 Turbo 3 Oil filter 4 Fuses 5 Auxiliary Stop 6 Alternator 7 Oil filler cap, engine 8 Oil dipstick 9 Fuel Filter 10 Fuel pre-filter with water separator 11 Control Unit, EMS 47710925 01-2019 © AB VOLVO PENTA...

  • Page 59: Engine, General

    Scrap the old filter. No cleaning or re-use is permissible • In continuous operation, the filter should be checked every 8 hours. For operations in extremely dirty environments such as coal mines and rock crushing mills, special air filters must be used. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 60: Charge Air Pipe, Leakage Check

    The alternator belts and drive belts have automatic belt tensioners and do not need to be adjusted. Check the condition of the drive belts. Replace as necessary; refer to Alternator Belt, Replace, page 60 and Drive belt, change, page 59. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 61: Drive Belt, Change

    8 Lift the 1/2" wrench and install the new drive belt. 9 Install the belt guards. 10 Install the fan guard and fan ring round the cooling fan. 11 Start the engine and perform a function check. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 62: Alternator Belt, Replace

    The oil change interval may under certain conditions be increased. To see if the engine complies Volvo Penta oil analysis needs to be performed. Contact your Volvo Penta dealer for further information. NOTICE! Oil change intervals must never exceed a period of 12 months.

  • Page 63: Oil Level, Checking And Topping Up

    Collect all the old oil and old filters, and hand them to a re-cycling station for destruction. 3 Remove the drain hose (or install the bottom drain plug). 4 Fill with engine oil. For change volume, please refer to Technical Data, page 85. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 64: Oil Filter/By-Pass Filter, Change

    6 Top up with engine oil, start the engine and let it run for 20-30 seconds. 7 Stop the engine, check the oil level and top up as required. 8 Check the sealing round the oil filters. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 65: Fuel System

    1 Put a collection vessel under the fuel filter to collect the condensate and fuel. 2 Open the drain nipple (1) in the base of the fuel pre- filter. 3 Tighten the drain tap (1) when fuel without water starts to run out. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 66: Engine Fuel Filter Replacement

    6 If a water trap is installed, change the filter in it at the same time as the fuel filter, and clean the water trap in the plastic bowl under the filter with a soft rag. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 67: Fuel Pre-Filter, Change

    Then tighten a further half turn, no more. 7 Connect the cable to the water trap sensor. 8 Where necessary, purge the fuel system; refer to Bleeding the Fuel System. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 68: Fuel System, Bleeding

    P0019904 2 Open the nipple on the front fuel connection. Connect a drain hose. P0019905 3 Purge the fuel system by pumping with the hand pump until fuel flows. P0019889 47710925 01-2019 © AB VOLVO PENTA...
  • Page 69 4 Close the venting nipple and remove the drainage hose. P0019905 5 Secure the hand pump. 6 Start the engine and allow it to idle for about 10 minutes. 7 Perform a leakage and function check. P0019904 47710925 01-2019 © AB VOLVO PENTA...

  • Page 70: Cooling System

    - in the worst case - can cause engine breakdown. Volvo Penta strongly recommend the use of our own coolants, ”Volvo Penta Coolant VCS Ready Mixed” or the concentrate ”Volvo Penta Coolant VCS”, which...

  • Page 71: Coolant Level, Checking And Topping Up

    Coolant filling must be performed with the engine stopped. Check the coolant level daily before starting. IMPORTANT: Only use coolant recommended by Volvo Penta. Top up with the same type of coolant as already used in the system. Different types of coolant must not be mixed.

  • Page 72: Coolant, Draining

    Do not use a high pressure power washer. Remove guards as necessary, to access the radiator. Clean with water and a mild detergent. Use a soft brush. Be careful not to damage the radiator vanes. Reinstall removed parts. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 73: Cooling System, Cleaning

    1 Empty the cooling system. Refer to Coolant, Draining, page 70. 2 Put a hose into the expansion tank filling hole and flush with clean water, as specified by Volvo Penta– refer to section Water quality in Technical Data, page 88 until the water draining out is completely clear.
  • Page 74 Maintenance 9 Fill up with Volvo Penta recommended coolant, following the instructions in the chapters entitled Maintenance, page 68 and Coolant Level, Checking and Topping Up, page 69. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 75: Inlet And Exhaust System

    AdBlue®/DEF has been added to the tank. IMPORTANT: The use of solution that do not fulfill the ISO 22241 standard will compromise the aftertreatment system P0024301 performance, increase emissions. Any warranty claims will be rejected. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 76 Damage and costs arising from a failure to meet these requirements are not covered by Volvo Penta warranty obligations. ® If AdBlue /DEF is filled from a can or pump that lacks...
  • Page 77 • Injectors may be damaged • The engine will no longer fulfill emission level requirements • Corrosion in the exhaust system between the turbocharger and aftertreatment system • Expensive repairs • Expensive repairs 47710925 01-2019 © AB VOLVO PENTA...

  • Page 78: Adblue/Def-Pump Filter, Change

    ® emptying of the AdBlue /DEF hoses. Disconnect the battery negative terminal. P0019364 Place a collection vessel under the filter cover. NOTICE! Use approved safety equipment and collection vessel. Undo the filter cover P0019389 47710925 01-2019 © AB VOLVO PENTA...
  • Page 79 Pull out the filter. P0019390 Install the new filter (1). Install the rubber gasket (2). Screw on the filter cover (3). P0019391 47710925 01-2019 © AB VOLVO PENTA...
  • Page 80 Tightening torque: 20 (+5) Nm (14.8 +3.68 Ibf. ft.) P0019392 Reconnect the battery negative terminal. Start the engine. Check for leaks; check function. Delete any fault codes. P0019365 NOTICE! Care for equipment and the remaining AdBlue®/DEF. p0013225 47710925 01-2019 © AB VOLVO PENTA...

  • Page 81: Electrical System

    Always stop the engine and break the current using the main switches before working on the engine. IMPORTANT: Contact a Volvo Penta dealer for information if any arc welding will be performed on the application. Arc welding can cause damage to the engine and the electronics.

  • Page 82: Battery

    • Charge the battery regularly. A battery that is kept fully loaded has a maximum service life. The easiest way to check if a battery needs charging is to use a voltmeter. 47710925 01-2019 © AB VOLVO PENTA...
  • Page 83 1 Connect the + cable (red) to the + pole on the battery and tighten the nut. 2 Connect the – cable (black) to the – pole on the battery and tighten the nut. NOTICE! Hand in the old battery to a re-cycling station. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 84: Storage

    It is of utmost importance that the conservation is performed correctly, therefore we have compiled a checklist covering the most important points. Before taking the engine out of service for long periods, Volvo Penta recommends that the engine is checked by a qualified workshop for possible need for overhaul or repair.
  • Page 85 2/3 diesel fuel. • Drain the conservation oil from the engine. • Bleed the fuel system. • Follow the other instructions on the previous page. * Conservation oils are sold by oil companies. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 86: Technical Data

    No. of cylinders Bore 123 mm (4.84 inch) Stroke 152 mm (5.98 inch) Displacement 10,84 dm (661 in Weight, wet (Engine) 1072 kg (2363 lb) Firing order 1-5-3-6-2-4 Compression ratio 17.0:1 Idling speed 600–900 47710925 01-2019 © AB VOLVO PENTA...

  • Page 87: Lubrication System

    NOTICE! Mineral-based oil, either fully or semi-synthetic, can be used on condition that it complies with the quality requirements above. VDS = Volvo Drain Specification Select the viscosity according to the table. The temperature values refer to stable ambient temperatures. * SAE 5W/30 refers to synthetic or semi-synthetic oils. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 88: Fuel System

    Sufficient fuel lubricity is essential to protect the fuel injection system against excessive wear. Restrictions for other diesel fuels Volvo Penta also approves the use of other diesel fuels as long as the here specified restrictions are followed. However Volvo Penta does not guarantee compliance with emission legislation or fulfillment of expected lifetime with these other diesel fuels.
  • Page 89 Volvo Penta also approves the use of fuel blends between these paraffinic fuels and diesel fuels that comply with the quality requirements. Service requirements •...

  • Page 90: Cooling System

    Follow the mixing recommendation on the product. The coolant should be mixed with distilled, deionized water. For Volvo Penta specified water requirements; refer to Water Quality, page 89. NOTICE! Always use “Ready Mixed” coolant if water quality cannot be determined or if it does not fulfill ASTM D4985.

  • Page 91: Water Quality

    Starter motor, Output 5,5 kW (7.4 hp) Battery electrolyte specific gravity at +25 °C: Fully charged battery 1.28 g/cm (1.24 g/cm Battery recharged at 1.20 g/cm (1.20 g/cm * Note. Applies to batteries with tropical acid. 47710925 01-2019 © AB VOLVO PENTA...

  • Page 92: Identification Numbers

    D 19329 A. Label part number B. EPA Engine family C. Power Category D. Date of manufacturing E. Model Year F. - G. - H. Exhaust Emission Control System Country of manufacture. P0020083 47710925 01-2019 © AB VOLVO PENTA...
  • Page 93 Applied standards: EN 61000–6–1:2007, EN 61000–6–2:2005, EN 61000–6–3:2007, EN 61000–6–4:2007, EN 12895:2015, EN-ISO 14982:2009 and EN 13309:2010. For engines equipped with the Volvo Penta Start/Stop System the responsibility for the functional safety of the system lies with the machine manufacturer performing the integration.

  • Page 95: Index

    Starting Using Auxiliary Batteries......39 Coolant, Draining............70 Stop the Engine............42 Cooling System........... 68, 88 Cooling System, Cleaning......... 71 Volvo Penta Action Service........19 Volvo Penta Dealer Network........18 DCU II (Display Control Unit)........45 Diagnostic Function...........44 Display Control Unit...........33 Warning Symbols............48 Draining condensate, fuel system......
  • Page 97 ‫من الممكن طلب دليل المشغل بلغة أخرى مجا ن ً ا عبر اإلنترنت لفترة تصل إلى 21 شهر ً ا من بعد‬ .‫التسليم‬ /http:// manual.volvopenta.com/coupon .Volvo Penta ‫إذا كان الوصول إلى اإلنترنت غير متاح، فالرجاء االتصال بوكيل‬ © 2019 AB VOLVO PENTA Volvo reserves the right to make changes...
  • Page 98 AB Volvo Penta SE-405 08 Göteborg, Sweden www.volvopenta.com...

This manual is also suitable for:

Tad1171veTad1172ve

Table of Contents