Table of Contents
Advertisement
OPERATIONS
Fill the solution tank to the desired level according to the marked
gauge on the clear hose on the right side of the tank.
DO NOT FILL PAST THE INLET LIP.
!
CAUTION:
IF A BUCKET IS USED TO FILL THE TANK, BE SURE IT IS CLEAN. DO NOT OVERFILL TO AVOID
POSSIBLE DISTORTION OF THE FLEXSOL DIAPHRAGM OR SOLUTION TANK. DO NOT USE WATER
TEMPERATURE THAT EXCEEDS 140° ° ° ° F (60° ° ° ° C). LIQUID DETERGENTS ARE PREFERRED, however if a
powered detergent is used, be sure it is fully dissolved. NOTE: If suitable powered detergent is used, premix
with hot water before filling the solution tank.
!
WARNING:
The internal parts of the pump used in the extractor are suitable for use with most carpet cleaning chemicals.
However, it is susceptible to chemical attack from cleaning substances, such as hydrocarbon solvents and
chlorinate bleaches. These noncombustible materials are not of the type normally used for carpet cleaning.
CHEMICALS:
SUITABLE CHEMICALS
Alkalis
Soaps
Detergents
Vinegar
Hydroxides
D-Limonene
@ When properly diluted
* Registered Trademark
FILLING THE VOYAGER
1.
Remove the Dome.
2.
Use a CLEAN bucket or hose to fill solution tank with hot water not to exceed 140°F (60°C). Do not fill above lower tank lip. Add non-
foaming carpet extraction chemical at recommended proportion. NOTE: If suitable powdered detergent is used, premix with hot
water filling the solution tank.
BEGIN CLEANING
1.
Adjust handle to comfortable position at waist level.
2.
Turn solution valve, located on bottom of rear position.
3.
Turn MAIN POWER switch ON.
4.
Adjust SPEED CONTROL KNOB on handle to set desired maximum speed.
5.
Turn SOLUTION switch ON.
6.
Lower BRUSH using left hand lever until contact with carpet is reached. Brush motor will start automatically.
NOTE: Incorrect brush height may trip circuit breaker or cause belt slippage. To correct, raise brush and reset circuit breaker
located on rear panel.
7.
Lower VACUUM using right hand lever. Vacuum motor will start automatically.
8.
Depress SPEED LEVER to propel machine. Speed is controlled by lever up to the maximum set on CONTROL KNOB.
NOTE: For protection, the Voyager will not operate in reverse when brush is on.
CLEANING PROCEDURE
1.
Operate machine in parallel passes, overlapping 2 inches on each pass. Turn SOLUTION switch OFF on turns. Propel machine gently
into turns. Abnormal turns may activate vacuum motor shut-off. Clean perimeter last.
2.
Run machine more slowly over spots or extremely soiled areas.
3.
Use right side of VOYAGER when cleaning against walls.
4.
Turn SOLUTION switch OFF 3 feet before completing a cleaning pass to ensure all solution is vacuumed from carpet.
CAUTION: WHILE OPERATING MACHINE, CHECK FOR EXCESSIVE FOAM BUILD-UP IN RECOVERY TANK. IF EXCESSIVE
FOAM IS PRESENT, ADD DEFOAMER SOLUTION TO RECOVERY TANK OR EMPTY RECOVERED SOLUTION.
5.
To speed dry, use a WINDBLOWER fan and ensure building ventilation system is ON.
6.
Empty recovery tank when full by releasing dump hose and removing stopper. NOTE: Vacuum motor will stop if recovery tank is full.
7.
Turn MAIN POWER switch OFF after use.
NOTE: Check the Circuit Breaker if the Voyager does not start.
8
DO NOT PUT DEFOAMER, SOLVENTS, SPOTTER OR PRESPRAY
CHEMICALS IN THE SOLUTION TANK.
@
VGR2 98448 7/1/97
TOP VIEW OF TANK
SOLUTION TANK
NONCOMPATIBLE CHEMCIALS
Aldehydes
Aromatic Hydrocarbons
SP Butyls
Carbon Tetrachloride
Chlorox*
Chlorinated Bleaches
RECOVERY TANK
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
Advertisement
Table of Contents
