Sylvania SPA124 - Bluetooth Speaker With Lighting And FM/Microphone Manual

Table of Contents

Contents

1 Packing list
2 Specification
3 Product overview
4 Documents / Resources
- 4.1 Download manual

Packing list

Upon opening the package, please check for the following items:
1 x Speaker
1 x Instruction manual
1 x Adaptor
1 x USB charging cable
1 x Microphone

Specification

Input: DC 5V
Drivers: 12"Full Range
FM: 87.5~108.0 MHz
Battery Capacity: 1500mAh
Transmission Distance: 10m
Unit dimensions: (WxHxD): 355 x 545 x 315mm

Product overview

Power / VOLUME -&+
Charging Indicator
RED = Charging
Light off = Fully Charged
DC interface (5V)
MODE / LED ON
(Long press to turn on/off light; Lightly press to enter into selection for Bluetooth, FM Radio, AUX Input, USB, TF)
Previous track & TWS
(TWS: Press and hold this button, the LED display shows: 't on' that means TWS in pairing mode. 't off' that means TWS in pairing off mode. 'bt st' flashing that means TWS is in the pairing mode, it will have a tone coming out when both speakers are connected successfully and the display shows 'bt' from the other speaker.
Play / Pause & REC
Under FM mode, short press the Play / Pause button, it can scan all radio stations and save it automatically.
Next track
TF / USB input
AUX input
MIC input

POWER SOURCE

Please charge the unit at least 4 hours before first time using.
Twist the dial clockwise/anticlockwise to switch on/off the unit.

CHARGE THE BATTERY

The charging LED lights on red during the battery charging. The LED will be off after fully charged.
When the battery is fully charged, please disconnect the charge cable from the speaker.

VOLUME

Twist the dial clockwise / anticlock wise to increase/discrease the mus volume.

PREVIOUS/NEXT BUTTON

Under playing status, press PREVIOUS / NEXT button to get back to a previous or next song.

PAUSE/PLAY BUTTON

To stop playing the current track, please press PAUSE / PLAY button on the control panel. Press it once again to continue playing.

MODE

Lightly press to enter into playing mode selection(Bluetooth, FM Radio, LINE Input, USB, TF).

LINE IN JACK

Connect an audio cable to the LINE IN JACK of the speaker and to the audio output socket on the external audio devices such as MP3 player, discman, etc, then select LINE by pressing the MODE button on the control panel.

Play from an external audi o d evice.

MIC IN JACK

Plug in microphone directly for playing.

USB JACK

Insert USB card directly for playing.

TF JACK

Insert TF card dirctly for playing.

Playing recording function

After the portable speaker is turned on, insert the TF Card or U disk to the TF slot or USB port, press the Mode button to the Bluetooth mode, connect it with your Bluetooth device and paly the music, long press the play / pause button around 3 seconds, you will here a prompt voice "ding" means the TF card / USB is starting recording, long press the play / pause button for 3 seonds again and you will here prompt voice "ding ding", that m e ans stop recording.
If you want to play this recording sound, press the Mode button to the USB or TF card mode, press the next button to find out this song and play it.

Note :

When your TF card and U disk insert to the speaker at same time, it will record to your U disk when recording.
The recording only works in Bluetooth mode, can not record in FM and AUX mode.
It's better to turn the Bleutooth devices volume to maximum during recording.
It will be stopped recording when pressing the mode button during recording.
It can't pause and can't go to next track or previous track during recording.

FM FUNCTION

Lightly press MODE button to switch to FM mode. Short press PLAY / PAUSE button on control panel for automatic searching and saving the radio stations, by pressing PREVIOUS or NEXT you can select a previous or next radio station.

Bluetooth:
Short press MODE button on control panel to select Bluetooth mode. Simultaneously turn on the Bluetooth setting on your phone, tablet or any other bluetooth enabled audio device and select "Syl SPA124" (no need to match code), the unit and device will then connected via Bluetooth. Press the "NEXT SONG" and "PREVIOUS SONG" button on the control panel to select the song, press " PLAY / PAUSE" button to control the playing status.

TWS: (True Wireless Speaker)

It needs two speakers to make a TWS. When you had two speakers, you can make a TWS as below steps:

Don't connect any Bluetooth devices to this speaker.
Turn on both speakers and press the mode button to change to Bluetooth mode.
Press and hold this button, the LED display shows: 't on', please wait for a few minutes, 'bt st' flashing that means TWS is in the pairing mode, it will have a tone coming out when both speakers are connected successfully and the display shows 'bt' from the other speaker. If you want it disconnect, please press and hold this button again.
Turn the Bluetooth devices to search the Bluetooth name "Syl SPA124" and tap to connect it. It will have a tone coming out from this speaker after connected successfully.
Now you can play the music form your Bluetooth devices.