Canon PIXMA mini260 Service Manual page 9

Ink tank not recognized.
No ink (no raw ink in a
new ink tank).
No ink (a used ink tank).
2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Blue (Power LED))
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on
the LCD.
Cycles of
blinking in
orange (Alarm
LED) and blue
(Power LED)
2 times Carriage error
3 times Line feed error
4 times Purge cam sensor error
5 times ASF (cam) sensor error
6 times Internal temperature error
7 times Ink absorber full
8 times Print head temperature rise
error
9 times EEPROM error
10 times VH monitor error
12 times AP position error
[1410 The following ink tank cannot be
to recognized. (U150)
1419] (Applicable ink tank icon)
[1688] Printer detected ink out condition of the
following ink. Replace the ink tank.
[1689] The following ink tank cannot be
recognized.
Error
Error
code
[5100]
[6000]
[5C00] An error occurred in the purge unit.
[5700]
[5400]
[5B00,
5B01]
[5200]
[6800]
[B200] The internal temperature exceeded the
[6A00] The AP motor does not move because the
Replace the ink tank.
Replace the ink tank, and close the printer cover.
By pressing the Stop/Reset button, printing can be
continued without replacing the ink tank, however, ink
may run out during printing.
Replace the ink tank, and close the printer cover.
By pressing the Stop/Reset button, printing can be
continued without replacing the ink tank, however, ink
may run out during printing.
Conditions
An error occurred in the carriage encoder
signal.
An error occurred in the LF encoder signal. - Paper feed encoder unit (QM3-
This error takes place when feeding paper
from the ASF after an error occurred in the
ASF cam sensor.
The internal temperature is not normal.
The ink absorber is supposed to be full.
Message on the LCD:
Ink absorber full. Service required.
Error codes:
5B00: Main ink absorber is full
(overseas).
5B01: Main ink absorber is full
(Japan).
The print head temperature exceeded the
specified value.
A problem occurred in writing to the
EEPROM.
specified value.
ASF unit, purge unit, or AP motor is faulty.
1-5
Solution
Replacement of listed parts,
which are likely to be faulty)
- Carriage unit (QM2-3987)
- Timing slit strip film (QC2-3208)
- Logic board ass'y (QM3-0110)
- Carriage motor ass'y (QM3-
0142)
0118)
- Timing slit disk (QC2-0211)
- Paper feed roller ass'y (QL2-
1691)
- Platen unit (QM2-3976)
- Logic board ass'y (QM3-0110)
- Paper feed motor ass'y (QM3-
0143)
- Purge unit (QM2-3980)
- Logic board ass'y (QM3-0110)
- Sheet feed unit (QM2-3992)
- PE PWB unit (QM3-0128)
- Logic board ass'y (QM3-0110)
- Carriage unit (QM2-3987)
- Logic board ass'y (QM3-0110)
- Absorber kit (QY5-0182)
- Print head (QY6-0069)
- Logic board ass'y (QM3-0110)
- Logic board ass'y (QM3-0110)
- Print head (QY6-0069)
- Carriage unit (QM2-3987)
- Logic board ass'y (QM3-0110)
- Sheet feed unit (QM2-3992)
- Logic board ass'y (QM3-0110)
- Purge unit (QM2-3980)
*1
*1
*1
*1
*1
*1
*1
*1
*1