Siemens SIPLUS ION ANALOGINPUT T001 Operating Instructions

SIPLUS CMS
Industrial I/O-Node
ION ANALOGINPUT T001
6AT8000-1BA00-0XA0
Operating Instructions (Compact)
ION ANALOGINPUT T001
Technical Data
Interfaces
IEEE1394a P1... P3
Number
Connector type
Transfer speed
Power Supply 24 V, 0 V, PD (Power Down)
Connector type
Clamping range
Input voltage
Power loss at 24 V DC
Current consumption at 24 V DC
Analog CH 01... CH 08
Number
Connector type
Transfer speed
Input voltage range
Input protection
Insulation
Input resistance
Input current
Sample frequency
Resolution
Coupling
Gain error
Offset error
Static offset
CMR
ION ANALOGINPUT T001
A5E02189572/A2, 02/2009, © SIEMENS AG 2008, 2009 Ⓟ 2009
Contact Information
SIEMENS AG
I IA SE DE
Würzburger Str 121
90766 FÜRTH
GERMANY
Customer Support
+49 (0) 180 5050 222
(€ 0.14 /min. from the German
landline network, deviating mobile
communications prices are possible)
Internet
www.siemens.com/siplus-cms
SIEMENS AG
Industry Sector
Postfach 4848
90026 NÜRNBERG
GERMANY
3
6-pin connector
400 Mbps
3-pin connector
(Phoenix Contact)
0.2 ... 2.5 mm²
18 ... 32 V DC
24 W
1 A
8
16-pin connector
(Phoenix Contact)
0.2 ... 2.5 mm²
± 10 V
± 60 V
± 0.4 kV
R ≥ 1 MΩ
l < 10 μA
≤ 40 kHz / analog input
16 Bit (15+1)
DC
0.025 % ± 1 digit
0.017 % ± 1 digit
Max. 0.12 %
100 dB
Scope of delivery
● ION ANALOGINPUT T001
● Operating Manual (compact)
Description
The ION ANALOGINPUT T001 is used to acquire analog signals
and to transmit the recorded data via the FireWire bus (IEEE1394a-
standard) with 400 Mbps to a higher level industrial PC. The use of
an ION ANALOGINPUT T001 allows recording 8 analog, separate
electrically insulated signals within a range of ± 10 V.
The maximum sample frequency is 40 kHz per analog input.
Assembling
The device must be mounted on a DIN rail. To avoid overheating
the minimum distances specified in the technical data must be
adhered to. Protective equipment and a disconnection unit for the
device must be provided.
Connecting
For clamping ranges: see technical data.
● Screw clamps: Screwdriver with a blade of 3 mm.
Recommended fastening torque: 0.2 ... 0.4 Nm.
● Ground Connection: TX 15 Torx screwdriver.
Recommended tightening torque: approx. 3 Nm.
Commissioning (hardware)
1. Connect the ION with a 24 V power supply. The green PWR
LED of the ION starts to blink.
2. Connect the ION with the PC via an IEEE1394 cable.
3. If the ION is being connected to the PC for the first time,
Windows will request a driver installation. To install the driver,
follow the instructions of the hardware assistant. The directory
for the drive installation is SIPLUS CMS\Drivers\IEEE1394.
4. After Windows has installed a driver for the ION, the ION can
be used with X-Tools. The yellow LNK LED of the ION lights up
and the hardware installation is complete when the ION is
connected to the PC, the driver is installed and X-Tools is
started.
Ground Connection
Connector type
Clamping range
Cables
FireWire
Analog inputs
Environmental Conditions / EMC
Transport and storage
temperature
Ambient temperature during
operation
Humidity rating
EMC interference emission
EMC interference immunity
Degree of protection
Constructive layout
Dimensions (H x W x D) in mm
Minimum distances:
Front
Top
Bottom
Design
Color
Weight
Mounting
Certificates
CE
M4 screw on the front:
SHIELD
Cable socket for screw M4
According to IEEE1394a
standard
Maximum length: 3 m
- 25 ... + 85 °C
0 ... +55 °C
5 ... 95 %, non condensing
EN 55011 (class A)
EN 61000-6-2:2005
IP20
200 x 60.2 x 126.5
80 mm
25 mm
25 mm
Aluminum / stainless steel
Silver
1 kg
DIN rail
EN 50022-35x15
thickness 2.3 mm
For use in industrial and office
areas