Summary of Contents for Siemens ION PROFIBUS DP SPY T001
Page 1
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Preface Scope of Delivery SIPLUS CMS4000 Product Characteristics Industrial I/O-Node ION PROFIBUS DP SPY T001 Installation and Maintenance 6AT8000-1BA00-5XA0 Notes on the CE Mark References Appendix Manual - English Release 2009-09...
Page 2
Trademarks All designations marked with ® are registered trademarks of Siemens AG. Other designations in this documentation might be trademarks which, if used by third parties for their purposes, might infringe upon the rights of the proprietors.
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Table of Contents Preface ..............................4 Purpose of this Document......................4 Validity of this Document........................4 Audience ............................4 Standards and Approvals.......................4 Scope of Delivery ..........................5 Scope of Delivery ...........................5 Unpacking and Checking .......................5 Product Characteristics ........................6...
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Preface Purpose of this Document This document supports you when commissioning and using the device • ION PROFIBUS DP SPY T001 Validity of this Document This document is valid for the following device: •...
Product Characteristics Introduction The ION PROFIBUS DP SPY T001 captures all of the data which is exchanged in between of any two devices which are present at the attached PROFIBUS DP bus and transmits the measured data to a superior industrial- PC via its FireWire (IEEE1394a-standard) link with 400 Mbps.
ION PROFIBUS DP SPY T001 6AT8000-1BA00-5XA0 User Documentation http://support.automation.siemens.com X-Tools - Standard Edition 6AT8000-0AB00-1BA0 X-Tools - Professional Edition 6AT8000-0AB00-2BA0 Further information is obtained from your local Siemens office and from the homepage http://www.siemens.com/siplus-cms. Manual - English A5E02186042 7 / 23...
Which network topologies can be realized? The IEEE1394a technology allows the building of extended networks with up to 63 participants. With the component ION PROFIBUS DP SPY T001, tree and chain topologies can be built. Caution The net topology is equal to the one of a bus with branching - but without loops! Tree topology The tree topology facilitates the building of networked systems by connecting two further nodes to each node.
SIPLUS CMS4000 Interfaces 3.5.1 Overview of Interfaces The device ION PROFIBUS DP SPY T001 provides three plugs for further SIPLUS CMS4000 components and one interface to connect the fieldbus solution PROFIBUS DP. ION PROFIBUS DP SPY T001 Manual - English...
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 3.5.2 IEEE1394a Interfaces At the ION PROFIBUS DP SPY T001 the IEEE1394a Interfaces (P1 / P2 / P3) are implemented as 6-pin- sockets. IEEE1394a Interfaces Caution Only cables of a maximum length of 4.5 m may be connected to the IEEE1394a Interfaces.
This means that only safety extra-low voltages (SELV) complying with IEC950/EN60950/VDE0805 can be connected to the power supply terminals. The power supply unit for the supply of the ION PROFIBUS DP SPY T001 has to meet NEC Class 2 (range of voltage 18-32 V, maximum load of 1 A).
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 3.5.4 Fieldbus Interface At the ION PROFIBUS DP SPY T001, the interface of the fieldbus solution PROFIBUS DP is implemented as a SUB-D-socket. fieldbus interface Manual - English A5E02186042 12 / 23...
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Indicators Name power indicator Description green Color no operating voltage Condition firmware operates blinks Name error indicator Description Color no error Condition error fan - if any Name indicator for the connection to the controller...
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Technical Data Connections Power Supply Interface 24V / 0V / PD Number Connector type 3-pin plug-in terminal block, Phoenix Contact Type input Input voltage 18 ... 32 VDC Typ. Power loss at 24 VDC 12 W Typ.
Page 15
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Permitted Cable / Cable Length FireWire according to IEEE1394a standard PROFIBUS DP according to PROFIBUS DP standard Permitted Environmental Conditions / EMC Ambient temperature during operation 0 ... +55 °C Transportation and storage temperature -25 ...
Installation and Maintenance Types of Installation Note The device ION PROFIBUS DP SPY T001 may exclusively be operated when installed on a DIN rail. Installation Installation of the device on a DIN rail: • Hang the upper table-track of the device on the DIN rail and push it down towards the DIN rail so that it snaps in.
• Disassemble the plug of the PROFIBUS DP connection cable. Removal of the device from the DIN rail: • Push the device down against the DIN rail and hang it out. disassembly of the ION PROFIBUS DP SPY T001 from the DIN rail Manual - English A5E02186042...
Technical data subject to change. Grounding The screw on the front side of the device is provided as grounding connection. Maintenance If a fault develops, please send the device to the Siemens logistics center. Address SIEMENS AG I IA RETOUREN-CENTER FUERTH SIEMENSSTR.
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Notes on the CE Mark Product Name ION PROFIBUS DP SPY T001 Device EMC Directive The product is designed for use in an industrial environment. Area of Application Requirements for...
This document does not contain complete detail information to the product due to reasons of clarity and can therefore exclude each thinkable case of assembly, usage or the maintenance. Further information is obtained from your local Siemens office and from the homepage http://www.siemens.de/siplus-cms.
Industrial I/O-Node - ION PROFIBUS DP SPY T001 SIPLUS CMS4000 Contact Information Address SIEMENS AG I IA SE DE WUERZBURGER STR. 121 90766 FUERTH GERMANY Internet http://www.siemens.de/siplus-cms Manual - English A5E02186042 23 / 23...