Table of Contents
Advertisement
Troubleshooting
■
Car Navigation, VCR, Camcorder, Rear View Camera, Rear Monitor
The connection of a car navigation system is not correct.
The picture from a car
aConnect it correctly.
navigation system is
Input setting of a car navigation system is not correct.
not displayed.
55
aCorrect the input setting.
The picture from a VCR or a
A VCR or Camcorder is not connected correctly.
aConnect a VCR or Camcorder correctly.
camcorder is not displayed.
Rear view camera is not connected correctly.
The picture from a rear
aConnect a rear view camera correctly.
view camera is not dis-
Input setting of camera is not correct.
played.
aCorrect the input setting.
The picture or the
AUTO
sound of the rear moni-
aSelect
tor is not switchable.
■
Display Settings
AUTO
The brightness of the
aSelect one of the dimmer levels from among 1 to 4 to make the dimmer
screen is not stable.
adjustment become free from light intensity.
The picture is dark.
The picture is whitish.
The screen is not adjusted properly.
Something is wrong
aMake every adjustment of the screen.
with the picture. The
picture is light in color.
The display does not
The monitor stops on the way to the home position.
a
go back into the unit.
Press [O/C] (OPEN/CLOSE).
Red, blue, or green
This is a characteristic of liquid crystal panels and is not a problem.
spots appears.
■
Remote control unit
The battery is inserted in the wrong direction. A wrong battery is inserted.
aInsert a correct battery in the correct direction.
The battery is weak.
aReplace the battery with new one.
No response to press-
The aiming direction of the remote control unit is wrong.
ing buttons
aAim the remote control unit at the sensor of the unit and press buttons.
The sensor is exposed to direct sunlight. (The remote control unit may not be
operable when the sensor is exposed to direct sunlight. In such a case, the
system is not faulty.)
aBlock off sunlight to the sensor.
56
CQ-VD7001N
(continued)
(AUTO) is not selected as the rear monitor setting.
AUTO
(AUTO) for the setting.
(AUTO) dimmer is selected.
■
Sound settings
No sound from left,
Cables are not correctly connected.
right, front, or rear
aConnect the cables correctly.
speaker.
Left and right sounds
The speaker leads are connected in reverse between right and left.
aConnect the speaker wires to the correct one.
are reversed.
No sound on the
The speaker setting is
aSet it correctly.
speaker.
Playing back a disc having a subwoofer channel
¡Subwoofer is set to
aSet subwoofer to
¡Down mix
No sound from the
aNo technical trouble. Cancel the down mix.
subwoofer
¡Private mode is set to
aSet private mode to
¡Pro Logic is set to
aSet Pro Logic to
❑
Error Display Messages
■
CD/MP3/WMA/DVD/VCD (Video CD)/CD Changer/DVD Changer
Display
Disc is dirty, or is upside down.
- E 1 -
aCheck disc.
Disc has scratches.
- E 2 -
aCheck disc.
No operation by some cause.
aPress [u]. If failure persists, press the reset switch. (Press the reset switch
- E 3 -
in the CD changer). If normal operation is not restored, call the store where
you purchased the unit or the nearest Panasonic Service Centre.
The type of the file that is selected is not supported.
- E 4 -
aCheck disc.
A WMA file can be copyrighted.
PROTECTED
aThe file protected by copyright is not playable.
No disc is in the player.
NO DISC
aInsert disc into the disc slot.
No magazine is in the changer.
NO MAGAZINE
aLoad the changer with CD-loaded magazine.
An attempt was made to play a disc with a region number other than "2" or
REGION ERROR
"ALL".
aPress [u] and check the disc.
Note:
¡ There may be cases when the disc numbers affected by an error are displayed before E1 and E2.
¡ Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the Operating
Instructions for the changer used.
(no) or
(none) .
NO
NONE
(no) in the speaker setting.
NO
(yes).
YES
(on).
ON
(off).
OFF
(on).
ON
(off).
OFF
Possible cause
a
Possible solution
CQ-VD7001N
56
57
Advertisement
Table of Contents
