Table of Contents
Advertisement
Settings
(continued)
(AUDIO continued)
TruBass
(TruBass Setting)
43
FRONT TruBass
(Applies to the front speakers)
[
: more
]
: less
REAR TruBass
(Applies to the rear speakers)
[
: more
]
: less
SUB-W TruBass
(Applies to the Sub-woofer)
[
: more
]
: less
Setting range: off, + 1 to + 10
Note:
¡ TruBass
TruBass is an audio technology to which the technique of
bass sound reproduction used in pipe organs is electrically
applied, and in which an equalizer is not used at all and
bass sound from the speakers to be used is richly repro-
duced.
Mixing
(Adjusts the SRS effect)
FRONT TO REAR Mixing
(Adjusts the SRS effect (front) on
rear speakers)
[
: more
]
: less
(Adjusts the SRS effect (centre)
CENTER TO REAR Mixing
on rear speakers)
[
: more
]
: less
Setting range: off, + 1 to + 10
: Previous menu
[MENU]
: Previous menu
[MODE]
(Remote Control)
44
CQ-VD7001N
SP SETUP
(Speaker set up)
Setting the absence/presence and size of each speaker
FRONT
(Front speaker setting)
LARGE
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL
: for small speakers, or when bass playback is
not possible
CENTER
(Center speaker setting)
LARGE
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL
: for small speakers, or when bass playback is
not possible
default: off
NONE
: when not using a center speaker
* A center speaker (option, EAB-CF2 recommended) is
required.
SURROUND
(Surround speaker setting)
LARGE
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL
: for small speakers, or when bass playback is
not possible
NONE
: when not using a surround speaker
SUB - W
(Subwoofer speaker setting)
: when using a subwoofer
YES
NO
: when not using a subwoofer
* A subwoofer (option, CJ-HD303N recommended) is
required. A power amplifier (option) is also required for
connecting a subwoofer.
default: + 5
Note:
¡While the private mode is active, only
adjusted.
: Quit
: Select/adjust
: Quit
[ENTER]
[]] [[] [}] [{]
: Select/adjust
SP LEVEL
Adjusting the output balance of each speaker
FRONT L
]
[
: down,
CENTER
]
[
: down,
default:
LARGE
FRONT R
]
[
: down,
R
SURROUND
¡
]
[
: down,
L
SURROUND
¡
default:
NONE
]
[
: down,
SUB - W
]
[
: down,
Setting range: –10 dB to +10 dB (1 dB steps)
A test signal (a continuous tone) is output from each
speaker for approximately 2 seconds.
Adjust the output balance so that the tone appears to have
the same volume from each speaker.
default:
LARGE
Adjusting the output balance:
Adjust the volume of all of the other speakers to the volume
level of the speaker from which the test signal appears to be
the quietest.
¡If the speaker setting is
speaker, the test signal is not output and that speaker
cannot be selected.
¡ Turn rotary volume controller or press [}] or [{]
default:
NO
(VOL) to adjust the volume of the test signal.
can be
FRONT
[MENU]
: Determine
(Remote Control)
SP DELAY
(Speaker level)
Adjusting the timing with which the audio from each speak-
er reaches the listener's position
(Left front speaker output bal-
ance)
CENTER
: up
]
: down,
(Center speaker output balance)
: up
(Right front speaker output bal-
ance)
SURROUND
: up
]
(Right surround speaker output
: down,
balance)
: up
(Left surround speaker output
balance)
¡Make this adjustment while listening to sound.
¡If the speaker setting is
: up
speaker cannot be selected.
¡When "PRO LOGIC" is displayed, 15 ms are automatically
(Subwoofer speaker output bal-
ance)
added to the delay time setting for the surround speakers.
MODE LEVEL
: up
Setting the VTR/AUX input level
Default: ± 0 dB for all speakers
Make this setting if it is not possible to adjust the volume
through the connected device (on the output side).
VTR LEVEL
LOW
HIGH
(none) or
(no) for a
NONE
NO
AUX LEVEL
LOW
HIGH
Note:
Note:
¡While the private
¡If the input level from VTR/AUX is too high, the audio will
mode is active, only
not be output normally.
and
FRONT L
¡After setting the input level
can be
FRONT R
The volume can be adjusted by pressing [}] or [{]
adjusted.
(VOL) on the remote control or turning rotary volume
controller on the unit.
: Previous menu
: Quit
: Previous menu
: Quit
[MODE]
[]] [[] [}] [{]
(Speaker delay)
44
(Center speaker delay time set-
ting)
[
: up
Setting range: 0 ms to 5 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
(Surround speaker delay time
setting)
[
: up
Setting range: 0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
(none) for a speaker, that
NONE
(Setting for VTR)
: sets the level low/sound volume increases
: sets the level high/sound volume decreases
default:
HIGH
(Setting for AUX)
: sets the level low/sound volume increases
: sets the level high/sound volume decreases
default:
HIGH
: Select/adjust
[ENTER]
: Select/adjust
: Determine
45
CQ-VD7001N
Advertisement
Table of Contents
