Table of Contents
Advertisement
Settings
(continued)
USER
SCREEN
AUDIO
DVD
INPUT/OUTPUT
DISPLAY UNIT
39
Display adjustment
TILT
(Tilt angle adjustment)
1
2
3
4
5
1
OPEN/CLOSE
(Monitor setting when power on)
AUTO
: the monitor is opened automatically when
turning ON ACC.
MANUAL
: the monitor is not opened automatically.
default:
Note:
¡The monitor position setting menu can also be displayed
by pressing the [TILT] button on the display unit for
more than 2 seconds.
(a
page 17)
CLOCK
Clock setting
DISPLAY
(Clock display)
OFF
: clock display OFF
ON
: clock display ON ("0:00" is displayed
before adjusting the clock.)
default:
CLOCK MODE
(Clock preference)
RDS
: the clock is automatically adjusted using
the RDS clock time service function.
(a
page 28)
MANUAL
: manually adjusted time is displayed.
default:
: Previous menu
[MENU]
: Previous menu
[MODE]
(Remote Control)
40
CQ-VD7001N
RADIO
HOUR ADJUST
(Hour adjustment)
]
: puts back hour
[
: puts forward hour
MINUTE ADJUST
(Minute adjustment)
5
]
: puts back minute
[
: puts forward minute
default:
5
Note:
¡To start the clock, touch/press
¡Set the Daylight Saving Time manually.
default: HOUR ADJUST: 0
TOUCH PANEL
MANUAL
Panel touch position adjustment
Position difference between the touching position and the
displaying symbol position may appear in the following sit-
uations:
1. The display position adjustment is executed.
2. The system is initialized.
3. The power is turned off soon after the touch panel is
adjusted.
For the cases above, readjust the touch panel position.
Note:
¡ This function can be performed on the touch panel.
This function is used only when there are some differ-
ences between the touching position and the symbol
position displayed on the monitor.
OFF
This function is not used ordinarily.
q Select
(yes) to proceed.
YES
w Touch the four corners of the touch panel counterclock-
RDS
wise.
e Touch
(yes) to reflect. To quit, touch
YES
(no).
: Quit
: Select/adjust
: Quit
[ENTER]
[]] [[] [}] [{]
: Select/adjust
r Touch fourth
q Touch first
ID-CODE
ID Code Setting
/ [MODE].
Prior to operating this unit, it is advisable to assign a 4-
digit ID code for security. Once the ID code has been set,
the unit cannot be operated if the main power supply is dis-
connected then re-connected. It is electronically locked so
MINUTE ADJUST: 0
that a thief cannot use the stolen unit unless that person
knows the code you have set.
The ID code operation must be performed only by the per-
son to whom the unit belongs.
Generally, it is not necessary to enter the ID code each
time when using the unit if it has not been disconnected
from the main power supply (car battery).
0
9
to
4 digits numeric code
How to set your ID code (for the first time)
q Enter an 4 digit ID code.
w Enter the same 4 digit ID code again.
How to change your ID code
q Enter the preset (old) 4 digit ID code. If the wrong ID code
is entered, a new ID code cannot be registered.
w Enter a new 4 digit ID code.
e Enter the new 4 digit ID code again.
How to cancel the known ID code
q Enter the preset (old) 4 digit ID code. If the wrong ID code
is entered, it is not possible to cancel the ID code function.
w Touch/press and hold
"Complete!" is displayed. The ID code cancelling proce-
dure is completed. The unit now works without an ID code.
Note:
¡ Should your unit ever require service, cancel your ID code
before sending for repair.
NO
¡ The ID code setting cannot be eliminated even by the
memory clear function.
¡ The inputted code is not displayed for your security.
[MENU]
: Determine
e Touch third
¡Record your registered ID code and keep it in a secure
location. If you forget it, you will be unable to use the
unit. In case you forget the ID code, please consult
your nearest Panasonic Service Centre.
MEMORY CLEAR
w Touch second
Memory clearance
The state of all of the current memories are returned to
default settings.
Note:
¡The ID code is not deleted by executing memory clear.
CANCEL
default: none
¡Be aware that this setting restores the unit to default
settings, so that all the memories and settings that
you have set will be eliminated.
/ [ENTER] until
: Previous menu
: Quit
: Previous menu
: Quit
[MODE]
[]] [[] [}] [{]
(Remote Control)
Caution
NO
: no memory clear.
The display returns to the previous one.
YES
: clears the memory to default settings
default:
NO
(really?) appears
REALLY?
when
is selected.
YES
: no memory clear.
OK
: proceed.
Caution
: Select/adjust
: ID code deletion
ID code deletion
[ENTER]
: Select/adjust
:
Determine
CQ-VD7001N
40
41
Advertisement
Table of Contents
