Table of Contents
Advertisement
Before you begin: This fireplace insert is supplied with a set of
seven ceramic fiber logs. Do not handle these logs with your bare
hands. Always wear gloves to prevent skin irritation from ceramic
fibers. After handling logs, wash your hands gently with soap and
water to remove any traces of fiber.
The positioning of logs is critical to safe and clean operation of this
fireplace. Sooting and other problems may result if the logs are not
properly and firmly positioned in the fireplace. Refer to Figure 20 and
Figure 21 and corresponding WARNING when completing follow-
ing log placement steps.
1.
Remove top louver, grasp louver, lift and pull forward.
2.
Lower bottom louver, lift and hinge forward.
3.
Release two glass frame spring clamps at bottom of the glass
door assembly.
4.
Swing the bottom of the glass door outward approximately
10-15 degrees, then grasping the edges, gently lift upward to
remove the door assembly, and set aside.
5. Remove the foam packaging that contains the log set from
inside the firebox.
6. Carefully unpack the logs and twigs. Spread them out for easy
identification.
7.
Begin with the front left and front right logs. Place these so that
they are centered left to right on the front log support ledge.
The flat bottoms will rest on top of the front log support ledge,
and they must be position all the way forward and touching
the back of the grate tangs. Two small tabs on the log support
keep the two front logs from shifting rearward. Important: The
front right log has a small knot as shown in Figure 20.
8.
Next install the large rear log. It will be centered left to right
and placed all the way to the back of the firebox, on top of
the rear log support. NOTICE: DV25IN models incorporate
two small tabs in the rear log support that keep the back log
positioned correctly. DV33IN models have one small tab in
the rear log support to ensure the back log is in the correct
position. The DV35IN models will have two tabs bent forward
in the rear log support to ensure proper left to right positioning
of the log, plus one small tab near the center that keeps the
back log from shifting forward.
9.
Locate the center left log. It will have two locator pin holes
on the bottom flat surface. Align the two holes with the two
left pins on the burner assembly. Make sure this log is not
raised up off of the burner. The flat bottom surface must be
completely resting flat on the top of the burner surface.
10. Install the center right log. It will also have two locator pin
holes on the bottom flat surface. Align these two holes with
the two right pins on the burner assembly. Make sure this log
is not raised up off of the burner. The flat bottom surface must
be completely resting flat on the top of the burner surface.
11. Add the right twig by placing the locator pin hole on the bottom
of the twig with the pin on top of the center right log. The tip of
the right twig will rest on top of the rear log near the right end.
12. Add the left twig by placing the locator pin hole on the bottom
of the twig with the pin on top of the center left log. The long
branch of the left twig will rest in a small groove on top of the
rear log. Note: The flat side of the twig will face the left side
liner. This groove is near the left end of the rear log.
13. Replace the glass door assembly onto the fireplace insert.
14. Secure the glass door with the two spring clamps located
under the firebox.
15. Re-install the upper and lower louver assemblies by aligning
the end tabs with the slots provided in the outer face flanges
of the insert.
Page 18
LOG pLACEMENT
Decorative Rock is not included with the Fireplace Insert,
however it may be purchased separately and placed only on the
firebox floor. Do Not place decorative rock or rock wool on the
logs or burner assembly.
Failure to position the parts in accordance with this dia-
gram or failure to use only parts specifically approved with
this appliance may result in property damage or personal
injury.
NOTICE: Center the front two logs on the front log support ledge.
Then make sure they are positioned all the way forward and touch-
ing the back edges of the grate tang uprights. The bottom of the
two front logs are flat and must sit on top of the front log support
ledge.
CAUTION
Figure 20
WARNING
Figure 21
32227-7-0115
Advertisement
Table of Contents
Troubleshooting
