Preference (Advanced); Volume Setup Sub-Menu - Onkyo TX-NR801 Instruction Manual

Preference (Advanced)

The "Preference" menu allows you to perform
miscellaneous settings for the TX-NR801/TX-NR801E.
/ / /
TUNING
PRESET
DIRECT / PURE AUDIO STEREO SURROUND THX DSP MEMORY FM MODE
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
5.Network Setup
→Basic Menu
[ENTER]Quit:[SETUP]
The illustrations used here represent the remote controller.
When you perform the procedures on the TX-NR801/
TX-NR801E, use the corresponding buttons on the front
panel.
1
First, press the RCVR button, and then
press the SETUP button to display the
main menu on the monitor and front dis-
play.
When the "Basic Menu" is displayed, select
"→Advanced Menu" using the
buttons and press the ENTER button to display the
"Advanced Menu."
2
Use the and
"4. Preference" and then press the ENTER
button.
The "Preference" menu appears.
3
Use the and
an item and then press the ENTER button.
4
Use the and
an item and then use the
buttons to set the desired value.
5 Press the SETUP button to return to the
main menu.
62
SETUP
SETUP
ENTER
RE TURN
A-FO RM LISTENING MODE MEMORY
ENTER
RCVR
SETUP
/ / /
ENTER
4.Preference
1.Volume Setup
2.Headphones Level
3.OSD Setup
4.OSD Position
[ENTER]Quit:[SETUP]
and
cursor buttons to select
cursor buttons to select
cursor buttons to select
and

Volume Setup Sub-menu

This sub-menu allows you to make various settings con-
cerning the volume control of the TX-NR801/
TX-NR801E.
a. Volume Display
You can choose from two ways of displaying the volume
setting on the screen.
Absolute: This displays the volume with a minimum
of 0 for no sound and a maximum of 100. As a refer-
ence, the volume setting of Ref (82) is equivalent to
0 decibels for the relative display method.
Relative: This displays the volume as a decibel
value on a scale with a designated reference point
that is displayed as 0, which equals the volume set-
ting of 82 of the absolute display method. With this
display method, the minimum value is –∞, the next
highest is –81, and the maximum value is +18.
b. Muting Level
This sets the attenuation level during playback when the
MUTING button is pressed on the remote controller.
This can be set to –∞, or between –50 and –10 decibels
in 10 decibel increments.
c. Maximum Volume
This setting allows you to set the maximum volume that
can be output with the MASTER VOLUME dial. Setting
a maximum volume allows you to prevent components
cursor
from being damaged by excessively loud volumes. For
the absolute volume display method, this can be set
between 50 and 99. For the relative volume display
method, this can be set between –32 and +17 decibels.
To not set a maximum volume, select "Off."
d. Power On Volume
This sets a designated volume to which the TX-NR801/
TX-NR801E will be set every time that the power is
turned on. This prevents the TX-NR801/TX-NR801E
from suddenly outputting very loud sounds if it is turned
on while it is set to an extremely high volume. For the
absolute volume display method, this can be set between
0 and 100. For the relative volume display method, this
cursor
can be set to –∞, or between –81 and +18 decibels. To
have the TX-NR801/TX-NR801E turned on with its cur-
rent volume setting, set this to "Last."
4-1.Volume Setup
a.Volume Display
:Absolute
b.Muting Level
:-oodB
c.Maximum Volume
:Off
d.Power On Volume
:Last
Quit:[SETUP]