Assembly; Operation - Flymo Minitrim ST Operation Instructions Manual

string etc, which can be thrown or become entangled in
the trimmer head.
Warning:
rotate after the machine has been switched off.
Warning:
while putting the upper and the lower shaft
together [Fig. A1].
Unplug the device immediately in case it doesn't stop
anymore.

2. ASSEMBLY

Danger!
Cut injury when the product starts
acciden tally.
v Before you assemble the product, make sure
that the mains cable is disconnected.
To assemble the trimmer [ Fig. A1/A2/A3 ]:
1
1. Put the upper shaft
until they make a click (click).
The product is correctly assembled when there is no
gap between the upper shaft and the lower shaft.

3. OPERATION

Danger!
Cut injury when the product starts
accidentally.
v Before you connect, adjust or transport the
product, disconnect the mains cable and
transport the product by the bottom handle.
To connect the trimmer:
v Connect the mains cable into a 230 V mains socket.
Work position [ Fig. O2/O3 ]:
1. Hold the product by the handle and the upper shaft
so that the trimmer head
forward.
2. Swing the trimmer head
area. Take small cuts.
Make sure, the filament does not touch hard objects such
as walls, stones and fences to prevent the filament from
welding together or breaking.
To start the trimmer [ Fig. O4 ]:
Danger!
Risk of injury if the product does not stop
when you release the start button.
41021-85.960.01.indd 5 41021-85.960.01.indd 5
The cutting line continues to
Beware of finger entrapment
Risk of physical injury!
2
and the lower shaft together
Risk of physical injury!
4
is tilted a small distance
4
in and out of the cutting
Risk of physical injury!
Do not lean over the trimmer guard – objects may be
thrown by the cutting line.
Don't use the trimmer for pond, river, stream, or creek
care. Water in the product could cause a malfunction, or
an electrical shock.
Do not operate the trimmer in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Trimmers create sparks which may ignite the dust
or fumes.
If the unit starts unintentionally when the mains plug
is connected, disconnect the mains at once.
Contact FLYMO to check the unit.
2. Put the cover 3 on the trimmer head
5
feed the cutting filament
cover 3 .
3
3. Push the cover into the trimmer head
3
cover anti-clockwise (see fig. A3) until it makes a click
(click).
v Do not bypass the safety devices or switches.
For example do not attach the start button
the handle.
To start:
ß
1. Push the safety interlock
S
2. Release the safety interlock
The product will start.
To stop:
q
v Release the start lever .
To extend the cutting filament (manual filament feed
system) [ Fig. O5/O6 ]:
1. Push and hold the two latches
5
2. Pull the filament gently until it reaches the filament
(14)
limiter .
(12)
3. Release the two latches
(12)
Make sure, the latches
4. Check that the filament cassette
locked (Try to remove the filament cassette
without to push the latches
5. Start the trimmer.
6. The filament 5 is automatically cut to the correct length
(14)
with the filament limiter .
If too much filament 5 has been pulled out, push the two
(12)
latches and turn the filament cassette
until the filament 5 is at the correct length.
4 while you
through the opening in the
4
and turn the
q to
q
and pull the start lever .
ß
.
S
(12)
.
.
(19)
are locked in the latches .
(15) is correctly
(15)
(12) ).
(15)
anti-clockwise
5
20.09.21 11:37 20.09.21 11:37