Maintenance; Storage - Flymo Minitrim ST Operation Instructions Manual

4. MAINTENANCE

Danger!
Cut injury when the product starts
accidentally.
v Before you maintain the product, make sure that
the mains cable is disconnected.
To clean the trimmer [ Fig. M1/M2 ]:
Danger!
Risk of injury and risk of damage to the
product.
v Do not clean the product with water or with
a water jet (in particular high-pressure water jet).
The airflow slots must always be clean.
1. Clean the airflow slots
(do not use a screwdriver).
2. Clean all movable parts after each operation. Especially
remove any grass and dirt from the cover
To replace the filament cassette or the cutting
filament:
Danger!
Risk of injury from metal cutting parts!
v Do not use metal cutting parts or replacement
parts and accessories not approved by FLYMO.
Only use original FLYMO Filament Cassettes.
You can order Replacement Filament Cassettes from
your FLYMO dealer or directly from the FLYMO
Customer Service. You can buy either a Replacement
Filament Cassette or the Cutting Filament only.

5. STORAGE

To put into storage [ Fig. S1 ]:
The product must be stored away from children.
1. Disconnect the mains cable.
2. Clean the product (see 4. MAINTENANCE).
3. Wind the cable around the cable hooks.
4. Store the product in a dry area where it has protection
from frost.
Recommendation:
The product can be hung up by the handle. The cutting
head is not put under too much strain if the product is
stowed hanging up.
6
41021-85.960.01.indd 6 41021-85.960.01.indd 6
Risk of physical injury!
Electric shock!
z
with a soft brush
3
.
Risk of physical injury!
For Minitrim ST Art. 9669519-01:
FLYMO Filament Cassette and Cutting Filament
Reference no.: FLY031 Part no.: 513106090
To replace the filament cassette [ Fig. M3/O6 ]:
1. Push and hold the two latches
2. Remove the cassette cover.
2. Remove the old filament cassette
3. Remove all dirt in the cassette holder
5
4. Release the filament from the cleat
(15)
filament cassette .
5. Pull approximately 10 cm of the filament
(15)
filament cassette through the hole
(18)
holder .
(15)
6. Put the filament cassette
Make sure, the filament is not caught and the latches
(19)
are locked in the latches
7. Check that the filament cassette
locked (Try to remove the filament cassette
without to push the latches
To replace the cutting filament [ Fig. M4/M5 ]:
1. Remove the filament cassette
2. Remove all dirt in the cassette holder
3. Take approximately 5 meters of the filament
insert it into one of the filament lock holes
(15)
filament cassette .
5
4. Wind the filament onto the filament cassette
the direction of the arrows on the top of the filament
(15)
cassette .
5
Make sure, the filament
filament cassette (15) .
5. Replace the filament cassette
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal
household waste. It must be disposed of in line
with local environmental regulations.
IMPORTANT!
v Dispose of the product through or via your municipal
recycling collection centre.
(12)
.
(15)
.
(18) .
ß
of the new
C
5 out of the
(17)
in the cassette
(18)
into the cassette holder .
(12)
.
(15) is correctly
(15)
(12) ).
(15)
.
(18) .
5
and
(20)
in the
(15)
in
is neatly winded on the
(15) .
20.09.21 11:37 20.09.21 11:37