Assembly Instructions - Flymo Contour 500 XT Original Instructions Manual

new one. Use only Flymo replacement cable.
11.Always wind cable carefully, avoiding kinking.
12.Never carry the product by the cable.
13.Use only on AC mains supply voltage shown on the
product rating label.
14.Our products are double insulated to EN60335.
Under no circumstance should an earth be connected
to any part of the trimmer.
Preparation
1. While using your product always wear eye protection,
substantial footwear and long trousers. Do not operate
the equipment when barefoot or wearing open sandals.
2. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
3. Inspect the area to be cut before each use. Remove all objects
such as stones, broken glass, nails, wire, string etc, which
can be thrown or become entangled in the trimmer head.
4 . Before use, inspect the area for wildlife, especially hedgehogs.
5. Check that the cutting head is fitted correctly.
Use
1. Use the trimmer only in daylight or good artificial light.
2. Avoid operating your trimmer in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Do not walk backwards when trimming, you could trip.
Walk never run.
6. Keep cutting head below waist level.
7. Switch off before pushing the trimmer over surfaces
other than grass.
8. Never operate the trimmer with damaged guards or
without guards in place.
9. Never fit metal cutting elements.
IMPORTANT If you want to use an extension cable when
operating your product, only the following cable dimen-
sions should be used.
- 1.0 mm 2 : max length 40 m
2
- 1.5 mm : max length 60 m
- 2.5mm 2 : max length 100 m
Minimum rating :
1.00mm 2 size cable, 10 amps 250 volts AC.
YOUR PRODUCT IS SUPPLIED WITH AN ELECTRIC MAINS
CABLE WIRED DIRECTLY INTO THE PRODUCT.
1.If the supply cord is damaged, it must be replaced by
your local Husqvarna UK Ltd. Approved Service Centre or
similarly qualified persons in order to avoid a hazard.
2.Flymo Extension Cables are available from your
local Husqvarna UK Ltd. Approved Service Centre.
3.Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd. Ap-
proved Service Centre for further information on the con-
nectors and kits available.
4.Only use extension cables specifically designed for out-
door use and which conform to one of the following spec-
ifications: Ordinary rubber (60245 IEC 53), Ordinary PVC
(60227 IEC 53) or Ordinary PCP (60245 IEC 57)
CONNECTORS Flymo connectors are suitable for use
with 2 core cable only. Under no circumstances should
these connectors be used for earthed products. All Flymo
connectors and cables are of splashproof construction. They
are not waterproof and must not be left outside permanently
nor should they be submerged or immersed in water. Do not
let cable lay or trail through pools of water or splashed with
A1

Assembly Instructions

A2
10.Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
11.Never pick up or carry a trimmer by the cable.
12.Do not lean over the trimmer guard - objects may be
thrown by the cutting line.
13.Beware of cut-off pieces of nylon line ejected during use.
14.Remove the plug from the mains :
- before leaving the trimmer unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your trimmer until you are
sure that the entire trimmer is in a safe operating condition;
- if the trimmer starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for
this product.
4. Only use replacement parts and accessories recom-
mended by Husqvarna UK Ltd.
5. After any maintenance in dealing with the cutting line,
always return the product to its normal operating posi-
tion before switching on.
6. Clean unit with a dry cloth. Never use metal objects to
clean the unit.
7. Inspect and maintain the trimmer regularly. Any re-
pairs must be carried out by an authorised repairer.
8. Store in a cool dry place and out of reach of children.
Do not store outdoors.
9. Allow the product to cool for at least 30 minutes be-
fore storing.
Cables
water from hose pipes.
MAINS PLUG REPLACEMENT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.
1.No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth be
connected to any part of the product.
2.Ensure the mains voltage suits your product.
3.IMPORTANT!
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - NEUTRAL
The wire which is coloured BLUE must be connected to the T ermi-
nal which is marked with the letter 'N' or coloured BLACK. The
wire which is coloured BROWN must be connected to the T ermi-
nal which is marked with the letter 'L ' or coloured RED.
4.It is important that the outer sheath is clamped correctly
into the 3-pin plug.
5.If in doubt consult your local Service Repairer or qualified
electrician before the machine is used.
6.A 13 Amp fuse must be fitted to the Mains Plug.
7.The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard against
electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Approved Service Centres which can
be found in your local Yellow Pages.
Assembly of Switch Handle to Tube (A1)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
BROWN - LIVE