NCR OPTIC 12 Installation Instructions Manual
Printer for wayne helix2.0
Hide thumbs
Also See for OPTIC 12:
- Installation instructions manual (154 pages) ,
- Installation instructions manual (90 pages) ,
- Installation instructions manual (80 pages)
Related Manuals for NCR OPTIC 12
Summary of Contents for NCR OPTIC 12
- Page 1 INSTALLATION INSTRUCTIONS NCR OPTIC 12 PRINTER FOR WAYNE HELIX2.0 6003-0105-8801 497-0529952 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
- Page 3 PREFACE Audience This book is written for end users (System Administrator and Maintenance Technician), NCR Field Engineering, and VAR/OEM Hardware and System Integrators Notice: This document is NCR proprietary information and is not to be disclosed or reproduced without consent.
- Page 4 SAFETY AND COMPLIANCE INFORMATION This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing the Wayne Helix Printer. Before proceeding, check the relevant hazard and safety information. Fire, explosion or electrical shock could occur and cause death or serious injury if these safe service procedures are not followed. All work must be carried out in accordance with NFPA (National Fire Protection Association) 30, 30A, and 70, and any local authority.
- Page 5 Read, understand and follow this manual and any other labels or related materials supplied with the equipment. If you do not understand a procedure, call NCR. It is imperative to your safety and the safety of others to understand the procedures before beginning work.
- Page 6 SAFETY SYMBOLS AND TERMINOLOGY Caution: This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazard. Obey safety directives that follow this symbol to avoid possible injury or death. Signal Words Warning: Alerts you to a hazard or unsafe practice which will result in death or...
- Page 7 If you do not have access to a computer, you may leave a voice message at: 1-800-528- 8658 (USA), or (International) +1-770-623-7400. When leaving a message, please provide a phone number and/or an email address so NCR can contact you if additional details are needed.
- Page 8 WARRANTY Warranty terms vary by region and country. All parts of this product that are subject to normal wear and tear are not included in the warranty. In general, damages due to the following are not covered by the warranty. •...
- Page 9 • Description of the problem, including any system error codes, error condition, or guidance to the area of failure. The NCR Agent will provide you with a work order number, which serves as your Return Material Authorization (RMA). Please provide the RMA on the outside of the shipping box.
- Page 10 viii...
- Page 11 REVISION RECORD Issue Date Remarks June 2021 First Issue...
-
Page 13: Table Of Contents
TABLE OF CONTENTS INSTALLATION COMPONENTS REQUIRED ADDITIONAL KITS WAYNE HELIX PRINTER KIT CONTENTS REQUIRED TOOLS INSTALL THE PRINTER ONTO THE HELIX OPTIC 12 PANEL PREPARE AND INSTALL THE HELIX OPTIC 12 PRINTER ASSEMBLY... -
Page 15: Installation Components
INSTALLATION COMPONENTS INSTALLATION COMPONENTS REQUIRED ADDITIONAL KITS Additional Required UL Listing Information Amount Required Retrofit Kits OPTIC 12 for Wayne UL Listed by Report Retrofit Kit Part Number One per side of the 6002-0008-8801 Helix 2.0 dispenser. WAYNE HELIX PRINTER KIT CONTENTS Note: Two kits are required for a full installation of the OPTIC 12 to the Wayne Helix 2.0 dispenser. -
Page 17: Required Tools
REQUIRED TOOLS REQUIRED TOOLS • 10mm socket or nut driver • Helix dispenser keys • Printer Door Key • Phillips #1 Screw Driver... -
Page 19: Install The Printer Onto The Helix Optic 12 Panel
2. Remove and retain the 2 nyloc nuts beneath the door stay assembly bracket using a 10mm socket or nut driver. Door stay arm (pictured below) will already be removed if doing this procedure in tandem with OPTIC 12 Helix 2.0 Installation Manual... - Page 20 INSTALL THE PRINTER ONTO THE HELIX OPTIC 12 PANEL Remove and discard the door stay assembly bracket paying attention to the door stay arm as applicable. Acquire the Helix printer assembly, (497-0529856) Printer Wall Support Bracket, (497-0528818) and attachment screws (006-8626492). Assemble Printer wall support bracket on top of helix printer assembly as shown below.
- Page 21 INSTALL THE PRINTER ONTO THE HELIX OPTIC 12 PANEL Fasten the printer and wall support assembly onto the Right side of the dispenser with 2 previously retained 10mm nuts and 2 provided 009-0008002 nuts using a 10mm socket or nut driver. TOP of ASSY BOTTTOM of ASSY Note: Ensure all cabling is routed behind center frame of pump cavity to ensure wiring does not interfere with weather seal...
- Page 22 INSTALL THE PRINTER ONTO THE HELIX OPTIC 12 PANEL 8. Plug in the Printer Power Cable (497-0513444) and Printer USB Cable (497-0515447) both cables preinstalled on the printer assembly to the OPTIC 12 head. 9 Continue to the next installation step in the Helix Installation Guide (497-0529910) UL Listed by Report Retrofit Kit 6002-0008-8801...