The Maintenance section contains the In addition, the Scotsman ICELINQ® app allows users instructions and schedules for the sanitation and to connect to the machine via Bluetooth® to monitor, cleaning of the machine.
MC0530 through MC1030 Remote Cooled User Manual Installation: Product Specifications Location Limitations Warranty Information This ice system is made up of three parts, the ice The warranty statement for this product is provided making machine, or head; the remote condenser; and separately from this manual.
Some installations require bin or dispenser adapters. of any part and/or other components not specifically See the table below. approved by Scotsman. Standard bin applications – Adapter information Scotsman reserves the right to make design changes and/or improvements at any time. Model B530P, B842S...
MAC condensers, kit number is RCKCME6GX. • Fan motor on all the time or controlled to be on whenever the ice machine is operating. • Non-Scotsman condensers must have prior Scotsman Engineering approval for warranty coverage to be in effect. June 2022 Page 5...
Testing has shown that using a filter that does not remove chlorine, such as the Scotsman Aqua Patrol, will greatly improve this situation, while the ice making process itself will remove the chlorine from the ice, resulting in no taste or odor impact.
MC0530 through MC1030 Remote Cooled User Manual Panel Removal 1. Locate and disengage the two quarter turn captured screws at the bottom of the front panel. 2. Pull the front panel out at the bottom. Dataplate Location 3. Lift the front panel up and off the machine. 1.
= Calculated Line Length Operating a machine with an unacceptable Configurations that do NOT meet these requirements configuration is misuse and will void the warranty. must receive prior written authorization from Scotsman. 40.35" Remote Condenser Located Condenser Distance & ABOVE Ice Machine Max 35’...
MC0530 through MC1030 Remote Cooled User Manual For The Installer: Remote Condenser Locate the condenser as near as possible to the Roof Attachment interior location of the ice machine. Install and attach the remote condenser to the roof Note: The location of the condenser is relative to the of the building, using the methods and practices of ice machine is LIMITED by the specification on the construction that conform to the local building codes,...
MC0530 through MC1030 Remote Cooled User Manual Line Set Routing and Brazing Do not connect the refrigerant tubing until all 7. Shorten tubing to correct length, clean ends and routing and forming of the tubing is complete. insert them into valve stubs. Final connections requires brazing, steps must Note: Be sure tube and stubs are round, dress with be performed by an EPA certified type II or higher...
MC0530 through MC1030 Remote Cooled User Manual Plumbing Requirements All models require connection to cold, potable water. 2. Connect drain tubing to drain fitting. A hand actuated valve within site of the machine 3. Route the drain tubing to building drain. Follow is required.
MC0530 through MC1030 Remote Cooled User Manual Electrical The machine is not supplied with a power cord, one 1. Remove the junction box cover and route the must either be field installed or the machine hard- power cord through the access hole and properly wired.
MC0530 through MC1030 Remote Cooled User Manual Final Check List: Lower Light and Switch Panel 1. Is the unit located indoors in a controlled environment? This user accessible panel provides important 2. Is the unit located where it can receive adequate operational information and duplicates the lights and cooling air? switches on the controller.
MC0530 through MC1030 Remote Cooled User Manual Initial Start Up 1. Remove front and left side panels. Check machine 6. When the ice has frozen enough, the Ready for for any packing or wires rubbing moving parts. Harvest indicator light will be on steady. After it’s Note location of control board in upper left corner been on steady for a few seconds Harvest will of the machine’s front.
MC0530 through MC1030 Remote Cooled User Manual Adjustments Ice Bridge Thickness Measurement Bridge Thickness - For the Service Tech Only Note: Indentations may be deeper on MC0322 and MC0330 1. Push and hold Off till the machine stops. 1/8-3/16” bridge 2.
The machine will fill up to that level and when it shuts process and then resume ice making. off the Bin Full indicator light will be On. Scan QR code to download the Scotsman ICELINQ™ App: Control Options Connect to this machine via Bluetooth to access additional machine operations, view error information, adjust settings, and initiate self-guided cleaning.
Preparing to Clean: Clean internal parts: 1. Remove the front panel. 6. Mix a cleaning solution of 6oz of Scotsman Clear 1 scale remover with 9 cups (72oz) of 105-115° F 2. Remove the evaporator cover. potable water. Scale Removal: 7.
Page 20
18. Push and release the “ON” button to resume ice making. Want more detail? Scan QR Code to download the Scotsman IcelinQ™ App to connect to this machine via Bluetooth and access the self-guided cleaning process. Exterior Panels Fingerprints, dust and grease will require cleaning with a good quality stainless steel cleaner.
If so, remove the ice and the machine All Prodigy ELITE® models are Bluetooth® enabled should start in a few minutes. and are compatible with the Scotsman ICELINQ® app, available on both the Apple App Store and To Manually Reset the machine.
Page 22
SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 www.scotsman-ice.com 800-726-8762 17-3737-03...