Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi R36LMW16
Summary of Contents for Ryobi R36LMW16
- Page 1 FRONT PAGE R36LMW16 R36LMW10...
-
Page 2: Intended Use
■ Do not use the product near drop-offs, IMPORTANT! ditches, excessively steep slopes, or It is essential that you read the instructions embankments. in this manual before assembling, operating, ■ Always wear safety glasses. and maintaining the product. ■ The product is capable of amputating hands Subject to technical modification. -
Page 3: Lawnmower Safety Warnings
BATTERY TOOL USE AND CARE ■ Do not incinerate the battery. ■ Read, understand, and always follow ■ Under abusive conditions, liquid may be the safety instructions which came with ejected from the battery; avoid contact. your battery and charger. Failure to do If contact accidentally occurs, flush with so may result in electric shock, fire or water. -
Page 4: Product Features
■ Turn on the product carefully according to ■ Injuries may be caused, or aggravated, by instructions, and keep hands and feet away prolonged use of the product. When using from the blades. Do not put hands or feet the product for prolonged periods, ensure to near or under rotating parts. -
Page 5: Transportation And Storage
■ When cutting long grass, reduce walking moving parts have come to a complete stop speed to allow for more effective cutting and before any cleaning or maintenance task. a proper discharge of the clippings. ■ Replace worn or damaged parts for safety. ■... -
Page 6: Symbols On The Product
SYMBOLS ON THE PRODUCT SYMBOLS IN THIS MANUAL Read and understand all Parts or accessories sold instructions before operating the separately product. Follow all warnings and safety instructions. Note Wear ear protection. Warning Wear eye protection. Do not operate the product on inclines greater than 15°. - Page 7 On/Off trigger Start button Motor control cable Telescopic handle Handle lock Safety key Height adjustment release lever Quick-release fastener Grass catcher Battery door Blade change u-bolt Rear wheel Front wheel Operator's manual Mulching plug Battery pack Charger R36LMW16 Know your product...
- Page 8 Wear full eye protection, ear protection, Set the handle in the correct operating Open the handle lock. non-slip heavy-duty gloves, substantial position. Ensure that the locking pin in footwear, and long trousers at all times the lower handle clicks into place. while operating the product.
- Page 9 Pull up the handle until it is fully NOTE: Make sure that the handle is Close the handle locks to secure the extended. fully extended so that the handle locks handle. can properly secure the handle. NOTE: The mulching plug covers NOTE: Insert the grass catcher frame For bagging operation, install the grass the rear discharge opening to allow...
- Page 10 Adusting the Using the grass Using the mulching Cleaning and p.14 p.11 p.12 p.18 cutting height catcher plug storing the product p.XX Cutting with EASY Emptying the grass p.15 p.14 p.17 Replacing the blade EDGE catcher...
- Page 11 USING THE GRASS CATCHER WARNING: Avoid holes, ruts, bumps, rocks, property stakes, or other hidden objects. WARNING: Do not operate the product on inclines greater than 15°. Mow across the face of slopes, never up and down. 1. Open the battery door. Insert the battery pack into the product.
- Page 12 4. Press the start button, then squeeze and hold either side of the on/off triggers to start the product. Release the start button and keep holding the on/off triggers to keep using the product. 5. Release the on/off triggers to stop the product.
- Page 13 1. Open the battery door. Insert the battery pack into the product. Make sure that the latch on the battery pack clicks in place, and that the battery pack is secured before operating the product. Insert the safety key. Close the battery door. NOTE: The product does not start without the safety key.
- Page 14 CUTTING WITH EASY EDGE EASY EDGE allows the product to easily cut the grass along walls or the edge of the lawn. NOTE: EASY EDGE pulls grass towards the blade when the product is running along a wall or the edge of the lawn. ADJUSTING THE CUTTING HEIGHT NOTE: Properly hold the carry handle while adjusting the cutting height.
- Page 15 2. Pull up or push down the deck to the preferred cutting height, using the height label as a reference. NOTE: The cutting height can be adjusted to 10 positions. Cutting heights may vary in particular products. Start the mower at the highest position, before cutting the grass.
- Page 16 2. Tilt the product on its side. 3. Remove all grass clippings and debris from the cutting deck and blade. WARNING: The blade on the product is sharp. Use extreme caution, and wear heavy- duty gloves when fitting, replacing, cleaning, or checking bolt security.
- Page 17 6. Install the new blade, washer, spacer, and nut. 7. Insert blade change u-bolt into the cutting deck holes to prevent the blade from spinning during tightening the blade nut. Hand-tighten the nut until the blade is secured and does not shake.Then use a spanner to further tighten the nut by 1/2 turn (35-40 Nm torque).
- Page 18 2. Raise the rear door, and remove the grass catcher. 3. Remove the grass clippings from the grass catcher into a bin. CLEANING STORING PRODUCT 1. Release the on/off triggers to turn off the product. 2. Open the battery door. Remove the battery packs.
- Page 19 3. Raise the rear door, and remove the grass catcher. 4. Remove all foreign materials from the product. Clean the product with a soft, dry cloth, or cleaning brush. WARNING: Do not use water to clean the product. 5. Open the handle locks. Push the upper handle into the lower handle until the handle is fully retracted.
- Page 20 7. Pull the quick-release fastener to unlock the lower handle. Fold down the lower handle, resting it on top of the product. 8. Fold the grass catcher and place it on top of the product. 9. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children.
-
Page 21: Battery And Charger
90.6 dB (A) accessories, keeping the hands warm (in case Uncertainty of measurement K = 3.0 dB of vibration), and organising work patterns. 94 dB (A) BATTERY AND CHARGER Model R36LMW16 R36LMW10 Battery pack BPL3660D Weight 1.96 Charger R36CHA4A0 BPL3620D, BPL3660D, BPL3690D,... - Page 24 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand RYOBI is a trade mark of Ryobi Limited, and is used under license. © 2021 Techtronic Cordless GP. 961478262-01...