Table of Contents
Advertisement
5.
Use "End time" to set the time at which the opera-
tion should end.
→ "Setting the end time", Page 16
→ "Time-setting options", Page 15
6.
Place the food in the cooking compartment before
the appliance starts to heat.
7.
Start the operation.
a The display shows the start time. The appliance is in
standby mode.
9 Rapid heating
To save time, rapid heating
ing time for set temperatures over 100 °C.
Rapid heating is possible for the following types of
heating:
¡ 4D hot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note: Do not set a cooking time until rapid heating has
come to an end.
10 Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
End time
Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
10.1 Setting the cooking time
You can set the cooking time for the operation of up to
24 hours.
Requirement: An operating mode and temperature or
setting have been set.
1.
Press "Cooking time".
2.
To set the cooking time, press the relevant time
value, e.g. hour display "h" or minute display "min."
a The selected value is marked in blue.
can shorten the preheat-
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
8.
When the operation has ended, remove the food
from the cooking compartment. The appliance auto-
matically switches off completely after approximately
15 to 20 minutes.
Note: If necessary, change the basic setting for the
lighting and the standby screen again.
1.
Set a suitable type of heating and a temperature of
at least 100 °C.
Rapid heating automatically switches off as of a set
temperature of 200 °C.
2.
Press "Rapid heating".
a "On" is in the tile.
3.
Use
to start the operation.
a Rapid heating starts.
a Once rapid heating is complete, a signal tone
sounds. "Off" appears for "Rapid heating"
4.
Place the food in the cooking compartment.
Cancelling rapid heating
▶
Press "Rapid heating".
a For "Rapid heating"
3.
Set the cooking time using
ment bar. Or enter the cooking time directly via the
number field
.
If required, use
to reset the adjustment value.
4.
Press "Apply".
5.
Use
to start the operation.
a The appliance starts to heat and the time counts
down.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
6.
Once the cooking time has elapsed:
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using
adjustment bar. Or enter the temperature directly via
the number field
.
3.
Press "Apply".
Cancelling the cooking time
You can cancel the cooking time at any time.
1.
Press the cooking time.
2.
Reset the cooking time using
Note: For operating modes that always require a
cooking time, the appliance resets the cooking time
to the preset value.
3.
Press "Apply".
Rapid heating en
.
"Off" appears on the display.
or
or via the adjust-
to switch the ap-
or
, or via the
.
15
Advertisement
Table of Contents
