Table of Contents
Advertisement
Press "Apply".
3.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
Press .
1.
a If information is available, this is displayed for a few
seconds.
If there is a lot of content, swipe down.
2.
If required, close the notification using
3.
8.8 Keeping warm over an extended period
You can use your appliance to keep meals warm for up
to 24 hours without changing the behaviour of the ap-
pliance. Use the time functions and change the basic
settings.
Note: If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
ensure that the behaviour of the appliance is not
changed during operation, only open the appliance
door once the set time has elapsed.
Change the "Lighting" basic setting to "Always off".
1.
→ "Basic settings", Page 20
Change the "Standby screen" basic setting to "On".
2.
Change the "Signal tone" basic setting to "Very short
3.
duration".
Rapid heating
9 Rapid heating
To save time, rapid heating
ing time for set temperatures over 100 °C.
Rapid heating is possible for the following types of
heating:
¡ 4D hot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note: Do not set a cooking time until rapid heating has
come to an end.
Time-setting options
10 Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
.
can shorten the preheat-
This ensures that the light in the cooking compart-
ment is always off while the appliance is operating
and when you open the appliance door, and the
time display does not change. The duration of the
signal tone is reduced at the end of the operation.
Set the required operating mode.
4.
→ "Setting an operating mode", Page 12
→ "Setting the type of heating and the temperature",
Page 12
Set the required cooking time depending on the op-
5.
erating mode.
→ "Setting the cooking time", Page 14
→ "Time-setting options", Page 13
Use "End time" to set the time at which the opera-
6.
tion should end.
→ "Setting the end time", Page 14
→ "Time-setting options", Page 13
Place the food in the cooking compartment before
7.
the appliance starts to heat.
Start the operation.
8.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
When the operation has ended, remove the food
9.
from the cooking compartment. The appliance auto-
matically switches off completely after approximately
15 to 20 minutes.
Note: If required, change the different basic settings
again.
Set a suitable type of heating and a temperature of
1.
at least 100 °C.
Rapid heating automatically switches on at temper-
atures of 200 °C and above.
Press "Rapid heating".
2.
a "On" is in the tile.
Press "Start" to start the operation.
3.
a Rapid heating starts.
a Once rapid heating has ended, a signal sounds.
"Off" appears for "Rapid heating"
Place the food in the cooking compartment.
4.
Cancelling rapid heating
Press "Rapid heating".
▶
a For "Rapid heating"
Rapid heating en
.
"Off" appears on the display.
13
Advertisement
Table of Contents
