Table Of Contents - Stanley Genesis 07537 Instruction And Service Manual

O R I G I N A L I N S T R U C T I O N
©2021 STANLEY Black & Decker
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically
or mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information
provided is based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening
pursues a policy of continuous product improvement and therefore the products may be subject to change. The information
provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered
Fastening cannot be held liable for any damage resulting from deviations from the original specifications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not
accept any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered
Fastening will not accept any liability for damage resulting from activities carried out by third parties. The working names,
trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free,
pursuant to the legislation with respect to the protection of trade marks.
1. SAFETY DEFINITIONS ................................................................................................................................................... 4
1.1 GENERAL SAFETY RULES .......................................................................................................................................................................... 4
1.2 PROJECTILE HAZARDS .............................................................................................................................................................................. 4
1.3 OPERATING HAZARDS ............................................................................................................................................................................... 5
1.4 REPETITIVE MOTIONS HAZARDS............................................................................................................................................................ 5
1.5 ACCESSORY HAZARDS .............................................................................................................................................................................. 5
1.6 WORKPLACE HAZARDS ............................................................................................................................................................................. 5
1.7 NOISE HAZARDS .......................................................................................................................................................................................... 5
1.8 VIBRATION HAZARDS................................................................................................................................................................................. 5
1.9 ADDITIONAL SAFETY INSTRUCTIONS FOR PNEUMATIC POWER TOOLS ................................................................................. 6
2. SPECIFICATIONS ............................................................................................................................................................ 7
2.1 SPECIFICATION FOR 07537 TOOL .......................................................................................................................................................... 7
2.2 TOOL DIMENSIONS ..................................................................................................................................................................................... 7
3. INTENT OF USE .............................................................................................................................................................. 8
4. PUTTING INTO SERVICE ................................................................................................................................................ 9
4.1 AIR SUPPLY .................................................................................................................................................................................................... 9
4.2 MECHANICAL CURSORS .........................................................................................................................................................................10
4.3 CURSOR ........................................................................................................................................................................................................11
4.4 LOADING AND RELOADING THE TOOL ..............................................................................................................................................11
4.5 LOADING THE TOOL .................................................................................................................................................................................12
4.6 RELOADING THE TOOL ............................................................................................................................................................................12
4.7 OPERATING PROCEDURE ........................................................................................................................................................................12
4.8 PLACING EQUIPMENT ..............................................................................................................................................................................12
5. SERVICING THE TOOL.................................................................................................................................................. 13
5.1 DAILY ............................................................................................................................................................................................................13
5.2 WEEKLY .........................................................................................................................................................................................................13
5.3 MOLYLITHIUM GREASE EP 3753 SAFETY DATA ...............................................................................................................................13
5.4 MOLYKOTE® 55M GREASE SAFETY DATA ..........................................................................................................................................14
5.5 MOLYKOTE® 111 GREASE SAFETY DATA ............................................................................................................................................14
5.6 SERVICE KITS ...............................................................................................................................................................................................15
6. MAINTENANCE ............................................................................................................................................................ 16
6.1 DISMANTLING 07537-00200 .................................................................................................................................................................16
6.2 PROTECTING THE ENVIRONMENT .......................................................................................................................................................18
6.3 GENERAL ASSEMBLY OF 07537-00200 TOOL ..................................................................................................................................19
6.4 PARTS LIST FOR 07537-00200 TOOL ...................................................................................................................................................20
7. PRIMING ...................................................................................................................................................................... 21
7.1 OIL DETAILS .................................................................................................................................................................................................21
7.2 HYSPIN® VG 32 AND AWS OIL SAFETY DATA ...................................................................................................................................21
7.3 PRIMING PUMP ..........................................................................................................................................................................................21
7.4 PRIMING PROCEDURE..............................................................................................................................................................................21
8. FAULT DIAGNOSIS ....................................................................................................................................................... 23
9. EC DECLARATION OF CONFORMITY .......................................................................................................................... 24
10. UK DECLARATION OF CONFORMITY........................................................................................................................ 25
11. PROTECT YOUR INVESTMENT! ................................................................................................................................... 26
E N G L I S H
3