Appendix D: Event Log Messages - Honeywell Galaxy 3-48C Programming Manual

Galaxy 3 Series Programming Manual

Appendix D: Event Log Messages

KEYPAD TEXT
0001 + CU-BATT Control Unit Standby Battery Low has occurred (battery voltage below 10.5 Vd.c.).
0001 - CU-BATT Control Unit Standby Battery Low has finished (battery voltage now above 10.5 Vd.c.).
0002 + CU-AC Control Unit Mains (a.c.) Power Fail has occurred.
0002 - CU-AC Control Unit Mains (a.c.) Power Fail has finished.
0003 + LID TAMP Lid Tamper on control unit has occurred.
0003 - LID TAMP Lid Tamper on control unit has finished.
0004 + AUX TAMP Auxiliary Tamper on control unit has occurred.
0004 - AUX TAMP Auxiliary Tamper on control unit has finished.
ABORT SET+ Setting process aborted
+AC+BATT AC Fail and battery voltage low.
+ AC FAIL AC Fail zone activated (opened) or an AC Fail on a Power Supply Unit.
AC Fail zone de-activated (closed) or an AC Fail on a Power Supply Unit has
– AC FAIL
stopped.
ALARM EXT+ Alarm extend zone activated.
ALM CAUSE Reset of system required by entry of an alarm cause code.
ADDED Engineer has added a module to the system.
ARC TEST Alarm Receiving Centre Test
ATM-1+ ATM-1 zone activated.
ATM-2+ ATM-2 zone activated.
ATM-3+ ATM-3 zone activated.
ATM-4+ ATM-4 zone activated.
AUTOTEST Automatic Test of the system via a comms module
AUTOTIMER + Autoset timer activated.
AUTOTIMER – Autoset timer de-activated.
BURG HIGH High priority intruder alarm zone open
BURG LOW Low priority intruder alarm zone open
+BAT FUSE Battery fuse on Power Supply Unit blown
+ BATT LOW Battery Low activated on Power Supply Unit.
– BATT LOW Battery Low de-activated on Power Supply Unit.
BEAM PAIR+ Beam Pair zones activated (opened).
BEGIN SET+ Setting process started
+ BELL FAIL Bell Fail zone opened
+ BELL TAMP Bell Tamper zone activated (opened).
– BELL TAMP Bell Tamper zone de-activated (closed).
CANCEL Alarm activation Cancelled by a valid user Code (system or Group(s) still Set).
COMM FAIL Communication Failure has occurred on a comms module.
CONFIRM Two independent alarms
COPY SITE Remote Copy of the Site (system) has occurred via Galaxy Gold or the RS232 Module. None
CUSTOM-A Custom-A zone activated (opened).
CUSTOM-B Custom-B zone activated (opened).
CU-FUSE + Control Unit Fuse trouble
DELAY ALM PA Delay Alarm zone activated after PA Delay timeout.
DL/SL ALM PA Delayed Silent zone activated after PA Delay timeout.
DOOR PROP MAX - Door left open
DR MASKED Detector masked. Activity monitoring of zone has failed.
DUAL Dual (Double Knock) zone activated (opened).
NOTE: M = Mandatory. NM = Non-Mandatory
NOTE: A plus (+) means an event has started. A negative (-) means an event has finished.
DESCRIPTION
D-1
Event Log
Trigger Event
13. Elec Status
M
20. Fault
13. Elec. Status M
13. Elec. Status
M
20. Fault
13. Elec. Status M
9. Tamper M
9. Tamper
M
18. Zone restoral
9. Tamper M
9. Tamper
M
18. Zone restoral
11. Reset NM
13. Elec. Status
M
20. Fault
13. Elec. Status
M
20. Fault
13. Elec. status
M
20. Fault
3. 24 Hours
M
16. Log Zone
Always TR M
9. Tamper M
Always TR NM
3. 24 Hours
NM
16. Log Zone
3. 24 Hours
NM
16. Log Zone
3. 24 Hours
NM
16. Log Zone
3. 24 Hours
NM
16. Log Zone
Always TR
None NM
None NM
2. Intrude
M
18. Zone Restoral
2. Intrude
M
18. Zone Restoral
13. Elec Status
M
20. Fault
13. Elec. status
M
20. Fault
13. Elec. status
M
20. Fault
2. Intruder NM
None NM
16. Log Zone NM
9. Tamper M
9. Tamper
M
18. Zone restoral
11. Reset/Cancel NM
20. Fault M
2. Intruder M
NM
5. Custom zones
NM
16. Log Zone
5. Custom Zones
NM
16. Log Zone
9. Tamper
13. Elec Status M
20. Fault
1. PA/duress M
1. PA/duress M
4. Security NM
15. Trouble
M
20. Fault
2. Intruder M