Page 1
All manuals and user guides at all-guides.com XR-MS5 XR-MS6 SIMPLE-2 A par t of contents is adequate. Re-issuing is under r equest. SERVICE MANUAL COMPACT DISC BASIC CD MECHANISM : AZG-X A1NM STEREO SYSTEM REMOTE SYSTEM SPEAKER CASSEIVER CONTROLLER XRMS5 CXLMS5 SXLMS5 RCBAT01...
All manuals and user guides at all-guides.com TABLE OF CONTENTS SPECIFICATIONS ................................3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING ................ 4 PRECAUTION TO REPLACE OPTICAL BLOCK ......................4 DISASSEMBLY INSTRUCTIONS 1 ..........................5 ~ 7 DISASSEMBLY INSTRUCTIONS 2 .......................... 8 ~ 13 ELECTRICAL MAIN PARTS LIST ...........................
All manuals and user guides at all-guides.com SPECIFICATIONS MAIN UNIT CX-LMS5/CX-LMS6 GENERAL TUNER Power requirements 230 V AC, 50 Hz Power consumption 45 W FM tuning range 87.5 MHz to 108 MHz Power consumption in standby mode FM usable sensitivity (IHF) 16.8 dBf With ECO mode on: 1.3 W FM antenna terminal 75 ohms (unbalanced)
All manuals and user guides at all-guides.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1 1. DISASSEMBLY OF AZG-X AND SERVICE POSITION 1) Disassembling the AZG-X (1) Remove the two screws (1) and remove the PANEL, SIDE R (2). (2) Remove the two screws (1) and remove the PANEL, SIDE L (2). (3) Remove five screws (1), (2) and (3), and remove the PANEL, TOP ASSY (4).
Page 6
All manuals and user guides at all-guides.com (5) Remove the FFC (1) and remove the two connectors (2) and (3). Remove the two screws (4) and remove the AZG-X (5). 2) CD Service Position (1) Install the CABI, FRONT ASSY. (2) Connect the FFC (1) to the connector (2).
Page 7
All manuals and user guides at all-guides.com 2. DISASSEMBLY OF HLDR, DOOR ASSY 1) Open the HLDR, DOOR ASSY and pull it in the direction of the arrow. 3. INSTALLATION OF HLDR, DOOR ASSY 1) Insert the HLDR, DOOR ASSY in the direction of the arrow. (Insert the boss of the CABI, FRONT ASSY into the holder of the HLDR, DOOR ASSY.) ...
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2 DISASSEMBLY AND REASSEMBLY OF AZG-X (30) AND AZG-A (10) 1) Removing the PWB, CD (1) Short the shorting-lands on the flexible card wire of the optical pickup by soldering. (2) Disconnect wires from the connectors CN706 and CN707.
Page 9
All manuals and user guides at all-guides.com 3) Removing the CD MECHA ASSY (1) Remove the SPR-E, MECHA. (2) Remove the hooks (at two positions) of the HOLDER MECHA and push down the CD mechanism and remove the CD mechanism. When reassembling it, align the positions of the rubber dampers and the damper hooks as shown.
Page 10
All manuals and user guides at all-guides.com 5) Removing the PLT, CD FR and LVR, ROLLER ASSY (1) Push down the LVR, ROLLER ASSY in the direction of the arrow. (2) Remove the four screws A. (3) Bend the mechanism and remove the boss. (4) Remove the PLT, CD FR.
Page 11
All manuals and user guides at all-guides.com 6) Removing the LVR, ROLLER ASSY (1) Insert the LVR, ROLLER ASSY L and R into the HLDR ASSY CLAMP. (2) Insert the SHAFT A into the BASE HOLE A. (3) Insert the GEAR,SHAFT B into BASE HOLE B. (4) Insert the SPRINGs C1 and C2 into the BASE SLITs C1' and C2'.
Page 12
All manuals and user guides at all-guides.com 7) Disassembling the LVR, ROLLER ASSY (1) Push the HLDR ASSY CLAMP and release the lock at the (A) position. (2) Remove the SHAFT ROLLER from the CLR ROLLER and remove the LVR, ROLLER ASSY (B). (3) Remove the SHAFT ROLLER and remove the ROLLER RUBBER.
Page 13
All manuals and user guides at all-guides.com 8) Removing the MOTOR ASSY (1) Remove the two screws A and remove the MOTOR. Reassembling MOTOR ASSY (1) Attach the MOTOR and PULLEY. MOT as shown below. (2) Align direction of the MOTOR ASSY label and fix it with the two screws A. LABEL LABEL PULLY...
All manuals and user guides at all-guides.com ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 87-010-831-080 C-CAP,U,0.1-16F 87-010-831-080 C-CAP,U,0.1-16F 8B-CL5-601-010 C-IC,LC876580W-5T99 87-010-831-080 C-CAP,U,0.1-16F 87-070-246-010 IC,GP1U271X 87-A10-520-000 CAP,E 3300-35 M SMG 87-A21-111-040 C-IC,M62495FP 87-010-831-080 C-CAP,U,0.1-16F 87-017-825-010...
Page 15
All manuals and user guides at all-guides.com REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C669 87-012-199-080 C-CAP,U 220P-50 J CH S108 87-A90-095-080 SW,TACT EVQ11G04M C670 87-012-199-080 C-CAP,U 220P-50 J CH S109 87-A90-095-080 SW,TACT EVQ11G04M C703 87-010-831-080 C-CAP,U,0.1-16F S110...
Page 16
All manuals and user guides at all-guides.com REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C825 87-A11-317-080 C-CAP,U 0.068U-16 K B CF832 82-785-747-010 CF,MS2 GHY,R C831 87-010-552-040 CAP,E 22-16 GAS CN991 87-A60-650-010 CONN,16P H GRY TUC-P16X-C1 C837 87-A12-022-080 C-CAP,U 0.22-16 Z F...
All manuals and user guides at all-guides.com REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C720 87-016-421-080 C-CAP,E 10-16 M WX C770 87-010-831-080 C-CAP,U 0.1-16 Z F C721 87-A10-589-080 C-CAP,E 100-10 M WX C771 87-012-272-080 C-CAP,U 680P-50 K B GRM C722 87-A10-260-080 C-CAP,U 0.1-16 K B...
All manuals and user guides at all-guides.com TRANSISTOR ILLUSTRATION E C B E C B B C E B C E 2SA1296 CSD655 2SB1370 2SB1677 CC5551 2SD2619 CSC4115 KTA1266 KTC3198 E C B DTC114ES 2SA1235 DTC114YKA 2SK2158 2SK360 KTC3199 2SA1369 KRA102S 2SC2714 KRA107S...
All manuals and user guides at all-guides.com ADJUSTMENT (TUNER / MICON) < TUNER SECTION > 1. Clock Frequency Check 8. FM Tracking Adjustment Settings : Test point : TP8 (Rch), TP9 (Lch) Settings : Test point : TP2 (CLK) Method : Set to MW 1602kHz and check that the test point is ...
All manuals and user guides at all-guides.com CD TEST MODE 1. How to Start the CD Test Mode While pressing the ENTER key, connect the AC power plug to the wall outlet. When the test mode starts up, all indicators light. 2.
Page 48
All manuals and user guides at all-guides.com 4. TRAY (Loading Mechanism) Test Mode When the TUNER/BAND key is pressed while all indicators light in the CD test mode, the display as shown appears. Pressing the TUNER/BAND key again returns to the CD test mode. 4-1.
All manuals and user guides at all-guides.com MECHANICAL PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 8B-CL5-048-010 PANEL,SIDE R(B) 31 8B-CL5-049-010 DUST COVER, CD LMS 2 8B-CL5-047-010 PANEL,SIDE L(B) 32 8B-CL5-044-010 CABI,FR(B) EZ<EZ>...
All manuals and user guides at all-guides.com CD MECHANISM EXPLODED VIEW 1 / 1 SHAFT, ROLLER SH, 4.5-2.1-0.25 W/O ADH SH, 6-2.55-0.5 W/ADH KSM-900AMA BASE 55 ...
All manuals and user guides at all-guides.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.
All manuals and user guides at all-guides.com SPEAKER PARTS LIST (SX LMS5) <YJ1BN> REF. NO. PART NO. KANRI DESCRIPTION 1 8B-CP5-001-010 PANEL,FR 2 8B-CP5-005-010 PANEL,TW 3 8B-CP5-003-010 GRILLE,FRAME ASSY 4 8A-CJ5-411-010 SPKR,W 87S 5 8A-CJ5-417-010 SPKR,TW 25 6 8B-CP5-610-010 CORD,SPKR 7 8A-CJ5-415-010 TERMINAL...
Page 59
All manuals and user guides at all-guides.com 211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9420025 2000045 921338 931261 Printed in Singapore...