Marantz SR5012 Service Manual page 145

Paths to be confirmed Display
DIGITAL fig.03a
A03Z2DIG
3
(ZONE2) fig.03b
***.*dB
fig.04a
A05HDMI
4 HDMI
fig.04b
***.*dB
Analog AD fig.05a
A06AD
5
fig.05b
(MAIN ZONE)
***.*dB
Analog Amp Assign
A07Z2ASS
6 (Amp Assign : fig.06
***.*dB
ZONE2)
1.6. Confirmation items for the video system
See the block diagram fig.XXth.
Paths to be confirmed Display
V01VIDEO
1 Analog Video pass fig.07
***.*dB
Video Convert
V02CONV
fig.08
2 (Analog or HDMI ⇒
***.*dB
HDMI)
HDMI pass
V03HDMI
3 fig.09
(MAIN ZONE)
***.*dB
Settings
Input Source : HEOS Music
Input Mode : Auto
Sound mode : STEREO
Amp assign : ZONE2
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Input Mode : HDMI (fixed)
Sound mode : STEREO
Amp assign : Surround Back
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Analog (fixed)
Sound mode : MULTI CH STEREO
Vol 60(-20dB)
Amp assign : Surround Back
Speaker Config ALL Speaker = Small/SW = Yes(2ch)
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Vol 60(-20dB)
Amp assign : ZONE2
MAIN ZONE : On
ZONE2 : On
Settings
Input Source : CBL/SAT
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Video Conversion (IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Video Conversion (IP Scaler) : OFF, All sources
MAIN ZONE : On
ZONE2 : Off
145
What to confirm
・ Digital(PCM) input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Digital(PCM) input ⇒ Pre OUT output (ZONE2 L/R)
・ HDMI input ⇒ Speaker output (Front L/R)
( b The input source can be switched to any source except CBL/SAT.)
・ Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・ Analog input ⇒ Pre OUT output SW(20Hz)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
What to confirm
・ CVBS input ⇒ CVBS output
・ Component input ⇒ Component output
( b The input source can be switched to any source except CBL/SAT.)
・ CVBS input ⇒ IP Scaler ⇒ HDMI output.
・ Component input ⇒ IP Scaler ⇒ HDMI output.
・ HDMI input ⇒ IP Scaler ⇒ HDMI output.
・ ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (MAIN function) ⇒ HDMI output (MAIN)
( b The input source can be switched to any source except CBL/SAT.)