Related Manuals for Fisher & Paykel RS7621WR
Summary of Contents for Fisher & Paykel RS7621WR
- Page 1 INTEGRATED COLUMN REFRIGERATOR FREEZER RS6121WR, RS7621WR, RS6121WL & RS7621WL models INSTALLATION GUIDE NZ AU GB IE...
-
Page 3: Table Of Contents
CONTENTS Cavity dimensions — 610MM + 610MM dual install Safety and warnings Integrated column models Cavity dimensions — 610MM + 760MM dual install Check your appliance Cavity dimensions — 760MM + 760MM dual install Remove pre-installed parts Toe kick panel dimensions — dual install Moving your appliance Power supply dimensions Electrical specification... -
Page 4: Safety And Warnings
SAFETY AND WARNINGS SAVE THESE INSTRUCTIONS WARNING! WARNING! Electric Shock Hazard To avoid hazard, follow these instructions carefully before installing or using this appliance. Failure to follow this advice may result in Please make this information available to the person installing the appliance. Assume all electrical parts are live. -
Page 5: Integrated Column Models
SAFETY AND WARNINGS INTEGRATED COLUMN MODELS Positioning inside the cabinetry Ensure the door of the appliance is closed when rolling into the cabinetry. Ensure the power cord is not run over or damaged when rolling the product into the cabinetry. Aligning inside the cabinetry For flush installation, ensure the door panels are installed flush with cabinetry front surface. -
Page 6: Check Your Appliance
CHECK YOUR APPLIANCE REMOVE PRE-INSTALLED PARTS Ensure you follow the unpacking steps printed on the packaging box of your appliance. Check that your appliance is the correct model as per your order. Check that the components and install kits are complete. Remove the trims kit at the back of the appliance. -
Page 7: Moving Your Appliance
MOVING YOUR APPLIANCE Follow the steps below to move your appliance to the install location. Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. Restrain the appliance with Remove the brackets from the strap and remove the remaining non-hinge side of the pallet. -
Page 8: Supplied Parts
SUPPLIED PARTS DOOR PANEL ATTACHMENT KIT INSTALL FASTENERS KIT Side bracket (6) Bracket slider (6) Side spacer bracket (6) Depth alignment gauge (4) Barbed plug (2) 8Gx16 Countersunk screw (7) For Custom door panels: M5x12 Cross-head screw (32) ANTI-TIP BRACKET ASSEMBLY MISCELLANEOUS PARTS Supplied in separate bags Hinge limiting pin (3) - Page 9 SUPPLIED PARTS TRIMS INSTALL KIT (EXTERNAL BOX) WATER FILTER KIT Top door panel side extrusion (2) Cabinet side trim (2) Collet locking clip (1) Water filter (1) Bottom drawer panel side extrusion (2) Bottom drawer top trim (1) 1/4” (6.35mm) Adaptor (2) 1/2 BSP Stainless steel braided hose with adaptor (1) MISCELLANEOUS ITEM PACK...
-
Page 10: Required Parts
REQUIRED PARTS TOE KICK PANEL INSTALL JOINER KIT Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer. Used for dual or multiple installation of appliances. Can be purchased separately through an Visit fisherpaykel.com for more information. authorised Fisher and Paykel dealer. -
Page 11: Door Panel Set
DOOR PANEL SET DOOR AND DRAWER HANDLE KITS Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. Select among the handle kit options below: HANDLE KIT RS61 RS76 Stainless steel door panel set Not supplied and must be purchased separately through an authorised Fisher CA 25725... -
Page 12: Hinge Change Kit
HINGE CHANGE KIT Not supplied and must be purchased separately. Available online at fisherpaykel.com. MODEL LEFT HINGE TO RIGHT HINGE KIT MODEL RIGHT HINGE TO LEFT HINGE KIT RS61 CA 848184P RS61 CA 848183P RS76 CA 848184P RS76 CA 848183P BRACKET ADAPT K05 BTM RH POCKET HINGE TOP RH BRACKET ADAPT COL K05 RH... -
Page 13: Product Dimensions - 610Mm Model
PRODUCT DIMENSIONS — 610MM MODEL PRODUCT DIMENSIONS A Overall height 2134 B Overall width C Overall depth* *Excluding front door panel. PRODUCT WEIGHT Weight (with packaging) Weight (without packaging) -
Page 14: Cavity Dimensions - 610Mm Model
CAVITY DIMENSIONS — 610MM MODEL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry. CAVITY DIMENSIONS A Overall height 2134 B Overall width C Minimum overall depth* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * Assumes a door panel thickness of 3/4”... -
Page 15: Door Panel Dimensions - 610Mm Model
DOOR PANEL DIMENSIONS — 610MM MODEL STAINLESS STEEL PANEL CUSTOM PANEL DIMENSIONS DIMENSIONS A Height of top door panel 1254 A Height of top door panel 1254 B Height of bottom drawer panel B Height of bottom drawer panel C Width of door/drawer panel C Width of door/drawer panel D Depth of door panel* D Depth of door panel*... -
Page 16: Custom Door Panel Install Dimensions - 610Mm Model
CUSTOM DOOR PANEL INSTALL DIMENSIONS — 610MM MODEL Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. Measurements of screw hole locations can vary depending on the height of toe kick 50 – 152mm. -
Page 17: Door Clearance - 610Mm Model
DOOR CLEARANCE — 610MM MODEL 115° DOOR OPENING 90° DOOR OPENING Insert hinge limiting pin Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top hinge. The hinge limiting pin limits the door swing to 90°. -
Page 18: Drawer Clearance - 610Mm Model
DRAWER CLEARANCE — 610MM MODEL DIMENSIONS A Maximum drawer extension when open* B Maximum drawer extension when open** * Excluding handle ** Including handle... -
Page 19: Toe Kick Dimensions - 610Mm Model
TOE KICK DIMENSIONS — 610MM MODEL STAINLESS STEEL TOE KICK PANEL CUSTOM PANEL TOE KICK PANEL Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel. For Custom door panel installation, a custom toe kick 2” – 6” (50 – 152mm) can be com for more information. -
Page 20: Toe Kick Install Options
TOE KICK INSTALL OPTIONS Standard toe kick height is For custom toe kick with 6" 4" (102mm) with Stainless steel (152mm) height. door panel. Min 2 7/8" (73mm) – max For custom toe kick 4" ( 102mm) toe kick depth with 2" (50mm) height measured from rear of door (extra lower grille attached). -
Page 21: Product Dimensions - 760Mm Model
PRODUCT DIMENSIONS — 760MM MODEL PRODUCT DIMENSIONS A Overall height 2134 B Overall width C Overall depth* *Excluding front door panel. PRODUCT WEIGHT Weight with packaging Weight without packaging... -
Page 22: Cavity Dimensions - 760Mm Model
CAVITY DIMENSIONS — 760MM MODEL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry. CAVITY DIMENSIONS A Overall height 2134 B Overall width C Minimum overall depth* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return Assumes a door panel thickness of 3/4”... -
Page 23: Door Panel Dimensions - 760Mm Model
DOOR PANEL DIMENSIONS — 760MM MODEL STAINLESS STEEL PANEL CUSTOM PANEL DIMENSIONS DIMENSIONS A Height of top door panel 1254 A Height of top door panel 1254 B Height of drawer door panel B Height of drawer door panel C Width of door panel C Width of door panel D Depth of door panel* D Depth of door panel*... -
Page 24: Custom Door Panel Install Dimensions - 760Mm Model
CUSTOM DOOR PANEL INSTALL DIMENSIONS — 760MM MODEL Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. Measurements of screw hole locations can vary depending on the height of toe kick 50 – 152mm. -
Page 25: Door Clearance - 760Mm Model
DOOR CLEARANCE — 760MM MODEL 115° DOOR OPENING 90° DOOR OPENING Insert hinge limiting pin Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top hinge. The hinge limiting pin limits the door swing to 90°. -
Page 26: Drawer Clearance - 760Mm Model
DRAWER CLEARANCE — 760MM MODEL DIMENSIONS A Maximum drawer extension when open* B Maximum drawer extension when open** * Excluding handle ** Including handle... -
Page 27: Toe Kick Dimensions - 760Mm Model
TOE KICK DIMENSIONS — 760MM MODEL STAINLESS STEEL TOE KICK PANEL CUSTOM PANEL TOE KICK PANEL Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel. For Custom door panel installation, a custom toe kick 2” – 6” (50 – 152mm) can be com for more information. -
Page 28: Dual Install Options
DUAL INSTALL OPTIONS The following are options for dual/multiple installation with reference to the door opening range and partition (optional) between two appliance combinations. Beware of clashing (circled) when opening the doors. Use a hinge limiting pin to restrict door opening rotation to 90°. Refer to ‘Door Clearance’ for more information. If installing a partition between two appliances, it must have enough clearance to ensure the doors/handles do not interfere with one another when opening or closing. -
Page 29: Cavity Dimensions - 610Mm + 610Mm Dual Install
CAVITY DIMENSIONS — 610MM + 610MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry. DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1219 C Minimum overall depth of cavity* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return Assumes a door panel thickness of 3/4”... -
Page 30: Cavity Dimensions - 610Mm + 760Mm Dual Install
CAVITY DIMENSIONS — 610MM + 760MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry. DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1372 C Minimum overall depth of cavity* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return Assumes a door panel thickness of 3/4”... -
Page 31: Cavity Dimensions - 760Mm + 760Mm Dual Install
CAVITY DIMENSIONS — 760MM + 760MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry. DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1524 C Minimum overall depth of cavity* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return Assumes a door panel thickness of 3/4”... -
Page 32: Toe Kick Panel Dimensions - Dual Install
TOE KICK PANEL DIMENSIONS — DUAL INSTALL STAINLESS STEEL PANEL CUSTOM PANEL toe kick panel toe kick panel door panels door panels TOE KICK PANEL (CA 25396) RS61 + RS61 MODELS TOE KICK PANEL RS61 + RS61 MODELS DIMENSIONS DIMENSIONS A Width of toe kick 1216 A Width of toe kick... -
Page 33: Power Supply Dimensions
POWER SUPPLY DIMENSIONS SINGLE INSTALLATION DUAL INSTALLATION Electrical connection must be within this space if located behind the appliance and ELECTRICAL AND PLUMBING CONNECTIONS must not protrude from the back wall. 1 Recommended location for connections in adjacent area or unit 2 Alternative location for connections at rear of cavity ELECTRICAL DIMENSIONS A Overall height of supply area... -
Page 34: Electrical Specification
ELECTRICAL SPECIFICATION PLUMBING SPECIFICATION Power cord Power cord Water hose Water hose Supply 230 VAC, 50 Hz Supply 1/2” (12.7mm) BSP Stainless steel braided hose with adaptor Service 10 amp circuit min 150kPa (22psi) / max 827kPa (120psi) Pressure kPa (psi) Socket 3-prong grounding-type @ 68°F (20°C) Total length of power cord exiting product... -
Page 35: Before Installation
BEFORE INSTALLATION Check the cabinetry Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity Dimensions' for the correct measurements. Check the power supply and water connections Ensure that there is a separate power socket for each appliance. Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance. -
Page 36: Install Anti-Tip Bracket
INSTALL ANTI-TIP BRACKET Anti-tip bracket overhead cabinetry assembly kit Locating the attachment position of anti-tip bracket back wall stud 1 Measure the height (A) of the attachment location from the floor to the alcove return and mark a horizontal line (B) at the back wall. - Page 37 INSTALL ANTI-TIP BRACKET Anti-tip bracket assembly kit Roll the appliance slowly into For plaster board wall 180mm the cabinetry until the anti-tip bracket overlaps the back edge Fix the anti-tip bracket to the of the appliance. wall with #10x40mm cross head screws, and screw tightly with a Ensure the bracket overlaps Anti-tip bracket (1)
-
Page 38: Connect Water And Power Supply
CONNECT WATER AND POWER SUPPLY Water fittings kit Connecting to water supply Collet locking clip (1) 1 Roll the appliance to the front of the cabinetry close enough to allow access at the back for power and water connection. 2 Insert the adaptor end of the braided hose through a hole at the rear of the plinth (A) and push all the way to the front of the appliance. - Page 39 CONNECT WATER AND POWER SUPPLY Water fittings kit 5 Insert the tube end of the adaptor fully into the Collet locking clip PLV (C) at the bottom front of the appliance. 1/2 BSP Stainless steel braided hose with adaptor (1) 6 Secure the connection with a locking clip between the PLV and hose end of adaptor (D).
-
Page 40: Position And Alignment In Cabinetry
POSITION AND ALIGNMENT IN CABINETRY Install fasteners kit Attaching the barbed plugs 1 Before rolling into the cavity, insert a barbed Barbed plugs (2) plug into a large hole at the top left side (A) of the appliance. The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance. - Page 41 POSITION AND ALIGNMENT IN CABINETRY Install fasteners kit Attaching the depth alignment gauges 1 Loosen the right and left screws at the top and bottom Cabinet depth alignment gauge (4) sides of the door. (A) 2 Locate the alignment gauges at correct orientation to the right and left screws.
- Page 42 POSITION AND ALIGNMENT IN CABINETRY Positioning into the cabinetry 180mm 1 Roll the appliance slowly into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold. Bracket PROFILE VIEW Be careful not to run over the water hose and power cord when rolling...
- Page 43 POSITION AND ALIGNMENT IN CABINETRY Tools Aligning with the depth gauges 1 Mark the step of the depth gauges (A, B) on both sides of the door based on the thickness of door panel. Example illustrations showing the door panel thickness Cross-head screwdriver (25.4mm ) marked on the gauges.
- Page 44 POSITION AND ALIGNMENT IN CABINETRY Tools Cross-head screwdriver Adjusting the alignment in the cabinetry Clockwise turn of the front and rear adjustment screws (A) raise the height of the appliance. Front foot Counter-clockwise turn of the adjustment screws lower Powered driver Rear foot adjustment adjustment...
-
Page 45: Secure Appliance To Cabinetry
SECURE APPLIANCE TO CABINETRY Install fasteners kit 8Gx16 Countersunk screw (6) Securing the top brackets Fix the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws. (A) Tools Cross-head screwdriver Powered driver (optional) Securing the side brackets Fix the side brackets (2x) to the lower right and left sides of the cabinetry with 8Gx16 countersunk screws. -
Page 46: Remove Hanging Brackets
REMOVE HANGING BRACKETS Tools Powered driver 1 Remove the M8 nut (A) and M8 washer (B) from the M8 screw at the top of the refrigerator door using the supplied hex key and spanner. M8 hex key Repeat step for the drawer door. Use a 13mm socket wrench top hanging bracket to tighten or loosen the M8 nut. -
Page 47: Install Door And Drawer Panels
INSTALL DOOR AND DRAWER PANELS STAINLESS STEEL PANELS CUSTOM PANELS Door handle kit Remove the protective film around the handle attachment area of the stainless steel panel before installing the handle. M5x25 Hex screw (4x) blue tape Tools Attaching refrigerator door handle Attaching refrigerator door handle 1 Refer to 'Custom door panel 1 Secure the door handle to the handle... - Page 48 INSTALL DOOR AND DRAWER PANELS Door panel STAINLESS STEEL PANELS CUSTOM PANELS attachment kit Attaching top hanging custom door panel bracket hanging bracket 1 Secure the top hanging bracket (A) to the screw Side bracket Attaching top hanging holes of the refrigerator bracket door panel with 8Gx16 1 Mark a line across...
- Page 49 INSTALL DOOR AND DRAWER PANELS Tools Hanging the refrigerator door panel 1 Hold the door panel at an angle towards the top of the refrigerator door (A). Powered driver (with 2.5mm drill bit) Cross-head screwdriver 2 Lower the screw holes of the hanging bracket onto the adjustment screws at the top of the refrigerator door.
- Page 50 INSTALL DOOR AND DRAWER PANELS Tools Ensure the side brackets are loosely screwed when adjusting the height of the door panel. Do not adjust the door panel height when the side brackets are screwed tight. This can generate friction which causes the hanging brackets to bend.
-
Page 51: Install Locking Bracket
INSTALL LOCKING BRACKET INSTALL ADJUSTMENT BRACKETS Tools Cross-head screwdriver Cutter M4 hex key (1) 1 Loosen the cap screws (C) of the adjustment brackets (D) on both 1 Loosen the screw at the bottom sides of the plinth with a hex key. of the refrigerator door, and slide 13mm spanner (1) the locking bracket (A) out until it... -
Page 52: Install Toe Kick Panel
INSTALL TOE KICK PANEL Miscellaneous components Attaching the mounting plate 1 Re-attach the toe kick mounting plate (A) to the plinth using same screws that were set aside previously. Air toe kick seal (1) 2 If toe kick depth is less than 92mm, attach an air toe kick seal (B) to the mounting plate. -
Page 53: Install Toe Kick Grilles
INSTALL TOE KICK GRILLES INSTALL TOP TRIM Tools Installing the top grille 1 Reattach the top grille (A) Cutter using the same screws set aside previously. Reinstalling the top trim Cross-head screwdriver 1 Slide one end of the top trim (A) into the hinge pocket of the appliance. -
Page 54: Install Water Filter
INSTALL WATER FILTER Supplied tools Inserting the water filter 1 Remove the packaging from the water filter. 2 Align the filter head with the Removing and replacing the filter slot of the filter removal tool Water filter (1) 1 To remove the water filter, and push until it clips in place. -
Page 55: Install Air Flow Divider
INSTALL AIR FLOW DIVIDER Miscellaneous The air flow divider blocks the air flow from bypassing the front of the bottom grille. components 1 Remove the adhesive layer (A) off the air flow divider. Flow divider cap (1) Tools 2 Reinstall the air flow divider (B) to the bottom of the freezer drawer with screw. -
Page 56: Install Cabinet Side Trims
INSTALL CABINET SIDE TRIMS Install parts Dual adhesive strips are pre-attached at four locations along the side trim. 1 Peel off the liners from the dual adhesive strips (A). 3 Hold the same angle and slide the side trim bottom end behind the lower Cabinet side trim (2) hinge down to the bottom... -
Page 57: Install Door And Drawer Side Trims
INSTALL DOOR AND DRAWER SIDE TRIMS Trims install kit Install door top extrusion Install drawer top and side trims Top door panel side 1 Align the top extrusion (A) 1 Remove the adhesive extrusion (2) to the top of the door, and backing of adhesive strips front of door match the notch (B) with the... -
Page 58: Dual Installation
DUAL INSTALLATION Install fasteners kit Attach central spacer to cabinetry 1 Measure the widths from the left (A) and right (B) cabinetry Cabinet depth alignment sides towards the centre to determine the spacer location. gauges (4) Refer to "Cavity dimensions' page for correct width of the Top joiner appliance. - Page 59 DUAL INSTALLATION Install fasteners kit Attaching the depth alignment gauges 1 Loosen the screws (A) at the cabinetry sides of the door and drawer of each appliance. 2 Locate the alignment gauges (B) at correct orientation to Cabinet depth alignment the right and left side screws.
- Page 60 DUAL INSTALLATION Tools Aligning the first appliance into the cabinetry min 7 1/16" (180mm) 1 Roll the first appliance (A) slowly into one side of the cabinetry until the anti-tip bracket (B) overlaps the back edge of the appliance. Cross-head screwdriver Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold.
- Page 61 DUAL INSTALLATION Install fasteners Adjusting the height of first appliance in cabinetry 8Gx16 Countersunk 1 Turn the front and rear screw (6) adjustment screws clockwise to raise height of the appliance Rear foot Front foot adjustment and counter-clockwise to adjustment screw screw lower the height.
- Page 62 DUAL INSTALLATION Tools Aligning the second appliance into the cabinetry min 180mm 1 Push the second appliance (A) to roll slowly into the other side of the cabinetry side by side with the first appliance. Cross-head screwdriver Ensure the bracket (B) overlaps the appliance by a minimum 180mm for a secure hold.
- Page 63 DUAL INSTALLATION Top joiner fastener kit M5x20 Cap screw (1) Securing the top brackets 1 Secure the top caps of both appliances to the central spacer with M5x20 cap screw (A) and washer (B). M5x16x1 Plain washer (1) 2 Secure the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws.
-
Page 64: Change The Door Hinges (Optional)
CHANGE THE DOOR HINGES (OPTIONAL) Tools You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. T2 star-head screwdriver ‘0’... - Page 65 CHANGE THE DOOR HINGES (OPTIONAL) Tools T2 star-head screwdriver Removing the top door hinge 1 Rotate the top hinge (A) outwards and remove the top hinge pocket cover (B) using the flat head screwdriver in the slot of the cover. 2 Unscrew M6x16 countersunk screws (C) to remove top hinge, and set aside to use later.
- Page 66 CHANGE THE DOOR HINGES (OPTIONAL) Tools Moving the sensor housing T20 star-head screwdriver Flat-head screwdriver 5 Reinstall the sensor 4 Move the sensor housing using #8x16 housing to align the 1 Unclip the hall sensor screws (2x) into the opposite hall sensor from the housing.
- Page 67 CHANGE THE DOOR HINGES (OPTIONAL) Hinge change assembly Reinstalling the top hinge 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws (A) on the new hinge Hinge (right or left) top side at the other side of the appliance. pocket (1) 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M6x16...
- Page 68 CHANGE THE DOOR HINGES (OPTIONAL) Hinge change assembly K05 top adaptor bracket R/L (1) use new top adaptor bracket K05 bottom adaptor Changing the top door bracket bracket R/L (1) 1 Unscrew the M5x10 screws (4x) to remove the top adapter bracket from the top of the door (A).
- Page 69 CHANGE THE DOOR HINGES (OPTIONAL) Tools T2 star-head screwdriver Reinstalling the door Flat-head screwdriver 1 Secure the door to the top and middle hinges of the appliance using M6x10 hex screws (4x). (A) Hex key 2 Activate the hinge spring by turning the star T20 screws to the I position.
-
Page 70: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door can open and close freely with no resistance from surrounding cabinetry. - Page 72 FISHERPAYKEL.COM © Fisher and Paykel Appliances 2020. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time.