Argox OS-2130DE User Manual
  1. Manuals
  2. Brands
  3. Argox Manuals
  4. Printer
  5. OS-2130DE
  6. User manual

Argox OS-2130DE User Manual

Ethernet printer
Hide thumbs Also See for OS-2130DE:
Table of Contents

Advertisement

Quick Links

Download this manual
Ethernet Printer
User's Guide
Version 1.03

Advertisement

Table of Contents
loading

Related Manuals for Argox OS-2130DE

Summary of Contents for Argox OS-2130DE

  • Page 1 Ethernet Printer User’s Guide Version 1.03...

  • Page 2: Table Of Contents

    8. RESET ETHERNET CARD 9. REBOOT ETHERNET CARD 10. ETHERNET CARD REPLACEMENT 10.1 A-2240E Ethernet Card Replacement 10.2 X-2300E/X-3200E Ethernet Card Replacement 10.3 CP-2140E Ethernet Card Replacement 10.4 OS-2130DE Ethernet Card Replacement 11. PRINTER UTILITY 11.1 Download/Upgrade firmware 11.2 Printer setting...
  • Page 3 Ethernet Printer Technical Manual November 10, 2010 11.3 Printer Info 12. SELF-TEST DIAGNOSIS 12.1 Perform Self-test Diagnosis...

  • Page 4: Ethernet Card Specifications

    Ethernet Printer Technical Manual November 10, 2010 1. Ethernet Card Specifications Items Specifications 32-bits, ARM-922, 100MHz 8 MBytes ( 4 M * 16Bits ) 4 MBytes Ethernet 1. Port: RJ-45 connector 2. LAN: 10/100 Mbps ( Auto Detect ) 3. Protocol: ARP, IP, ICMP, UDP, TCP, HTTP, DHCP, rawTCP, LPR, IPP, SNMPTrap 4.

  • Page 5: Additional Commands

    Ethernet Printer Technical Manual November 10, 2010 2. Additional Commands Parameter types: None: no parameter is required Signed integer. e.g. +100 or –23 Unsigned integer. e.g. 32 Signed byte. Just one byte binary data. e.g. +3 is represented as 0x03(03H), and –1 as 0xff (0FFH). Command Description <ESC>KIZA...
  • Page 6 Ethernet Printer Technical Manual November 10, 2010 printer status. (default value:1) This command is for Ethernet card to enquire Printer. <ESC>KJOETHERNET *Ethernet IP addresses *Syntax: <ESC>KJOETHERNETm,m,m,m,n,n,n,n,o,o,o,o,q,q,q,q,q,q *Parameter: “m,m,m,m,”: IP address “n,n,n,n,”: subnet mask “o,o,o,o,”: gateway “q,q,q,q,”: MAC address Parameters must be HEX values. *Example: IP address:192,168,0,42 (“m,m,m,m,”=”0xC0 0x2C 0xA8 0x2C 0x00 0x2C 0x2A”)
  • Page 7 Ethernet Printer Technical Manual November 10, 2010 This command is for configuring the Ethernet card. <ESC>KJR * Ethernet card version. *Syntax: <ESC>KJRm,nn *Example: <ESC>KJR5,21; Ethernet card version is 5,21. After upgrading the firmware, the Ethernet card will send this command to the printer. Use the printer self test to get the Ethernet card version.
  • Page 8 Ethernet Printer Technical Manual November 10, 2010 “b,b,b,b,”: subnet mask “c,c,c,c”: Ethernet card gateway Parameters must be HEX values. *Example: IP address:192,168,0,42 (“a,a,a,a,”=”0xC0 0x2C 0xA8 0x2C 0x00 0x2C 0x2A 0x2C” ) If “a,a,a,a,”=”0x00 0x2C 0x00 0x2C 0x00 0x2C 0x00 0x2C”, the setting will become DHCP (auto IP address).
  • Page 9 Ethernet Printer Technical Manual November 10, 2010 3. 8MB D: 8GB 4. 16MB E: 16GB 5. 32MB 6: 64MB 7: 128MB 8: 256MB 9: 512MB Available Flash Memory Size DT/ TT 0: DT mode 1: TT mode Media Sensor Type 12 0: Reflective 1: See Through1 2: See Through2...
  • Page 10 Ethernet Printer Technical Manual November 10, 2010 Label Size Origin Coordination Shift External Card RTC card :0x3000000 Chinese font:0x2010000 Taiwan font :0x2020000 Korean font :0x2040000 Japanese font 0x2080000 Flash Module 0:External 1:Internal 2: Internal Serial COMM. abcd 0000 total: 8 bytes a (Baud Rate) b (Parity) c (Data Bit)

  • Page 11: Table 2

    Ethernet Printer Technical Manual November 10, 2010 TABLE 2 8 bit data Symbol Set 7 bit data Symbol set (a=0) (Code page) (a=1) English (437) USASCII Latin 1 (850) British Slavic (852) German Portugal (860) French Canadian/French Danish (863) Nordic (865) Italian Turkish (857) Spanish...

  • Page 12: Ethernet Printer Status/Activity Indicators

    Ethernet Printer Technical Manual November 10, 2010 3. Ethernet Printer Status/Activity indicators 3.1 Ethernet Module Status/Activity indicators LED Status Description Off (both LEDs) No Ethernet link is detected. Green Speed LED On: 100 Mbps link Off: 10 Mbps link Amber Link/Activity LED On: link up Off: link down...

  • Page 13: Obtaining The Ip Address

    Ethernet Printer Technical Manual November 10, 2010 4. Obtaining the IP Address Printer can obtain the IP addresses from the following modes: A. Using router or similar device to assign the IP address to the printer 1. Connect both PC and printer using the internet cable to the Router LAN port. 2.
  • Page 14 Ethernet Printer Technical Manual November 10, 2010 3. Search the IP address of the Router assigned to the printer. The following is an example of using the 3COM WL-602 Router. Launch the web browser and enter the default IP address to open the Router homepage (For example: The default IP address of the 3COM WL-602 Router is http://192.168.1.1) When the printer is turned on, READY LED will blink.
  • Page 15 Ethernet Printer Technical Manual November 10, 2010 address; otherwise this will delay the time for the printer to get ready. B. Using the Ethernet card static IP address Connect the printer and the PC using the cable. Turn on the printer and wait for about 1 minute. The printer will automatically get the default IP addresses (192.168.1.100).

  • Page 16: Information And Setting

    Ethernet Printer Technical Manual November 10, 2010 5. Information and Setting 1. Launch a browser and enter the printer IP address. You can view the Ethernet card (SERVER STATUS) and printer (PRINTER STATUS) related status information.
  • Page 17 Ethernet Printer Technical Manual November 10, 2010 2. In the CONFIG’s TCP/IP submenu, you can configure how the Ethernet card assigns the IP address to the PC and other related settings. 3. In the Maintenance submenu, you can update the firmware of the Ethernet card/printer. The accumulative time will be reset if the printer shuts down.

  • Page 18: Ethernet Port Setting

    Ethernet Printer Technical Manual November 10, 2010 6. Ethernet Port Setting 1. Run the Seagull Driver file. 2. The Windows Printer Drivers\License Agreement window appears on the screen. Read the license agreement and select “I accept the terms in the license agreement”, then click Next. 3.
  • Page 19 Ethernet Printer Technical Manual November 10, 2010 4. Select the appropriate options, and then click Finish to start the software installation. 5. Windows Printer Driver installation starts. 6. A Welcome to the Seagull Driver Wizard window appears on the screen. Select Install Printer Drivers, and click Next.
  • Page 20 Ethernet Printer Technical Manual November 10, 2010 7. Select Install a driver for another printer, then click Next. 8. Select the model of your printer, and then click Next.
  • Page 21 Ethernet Printer Technical Manual November 10, 2010 9. Click the Create Port button. 10. Select Standard TCP/IP Port, and click the New Port button.
  • Page 22 Ethernet Printer Technical Manual November 10, 2010 11. A Welcome to the Add Standard TCP/IP Printer Port Wizard window appears on the screen, click Next. 12. Enter the IP address, and then click Next.
  • Page 23 Ethernet Printer Technical Manual November 10, 2010 13. Select Standard, and then click Next. 14. Click Finish to complete the current wizard installation.
  • Page 24 Ethernet Printer Technical Manual November 10, 2010 15. Return to Specify Port window, and click Next. 16. Specify the printer name, and then click Next.
  • Page 25 Ethernet Printer Technical Manual November 10, 2010 17. Click Finish to complete the driver installation. 18. A Seagull Driver Wizard Completed Successfully window appears on the screen. Click Close.
  • Page 26 Ethernet Printer Technical Manual November 10, 2010 19. Choose Raw(R) or LPR(L) in the Protocol option, and then click OK. 19.1 Raw(R) settings as below: 19.2 LPR(L) settings as below:...
  • Page 27 Ethernet Printer Technical Manual November 10, 2010 Because LPR(L) does not support the bidirectional function, you must disable “Enable bidirectional support” option. ! 20. LPD/LPR setting is complete.

  • Page 28: Lcd Ethernet Setting

    Ethernet Printer Technical Manual November 10, 2010 7. LCD Ethernet Setting LCD Function Function Options Description Display DHCP DISABLE If printer is not connected to a router, with DHCP disabled, settings of IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY settings will be available on LCD.
  • Page 29 Ethernet Printer Technical Manual November 10, 2010 SUBNET MASK, enter DEFAULT GATEWAY setting, press CANCEL button once; LCD will prompt “ETHERNET CARD UPDATE FINISH…” 5. Restart the printer. Note: All settings are valid, if IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY settings are complete and printer is restarted.

  • Page 30: Reset Ethernet Card

    When IP address setting is complete, the user must restart the printer to check the IP address on the webpage. If the printer cannot get the correct IP address, please reset or reboot the Ethernet Card. Model OS-2130DE X-2300E A-2240E Reset X-3200E...

  • Page 31: Reboot Ethernet Card

    Ethernet Printer Technical Manual November 10, 2010 9. Reboot Ethernet Card When the Ethernet card is not functioning normally, we can restore its default settings by following these steps: 1. Turn off the printer and remove all the printer covers. 2.

  • Page 32: Ethernet Card Replacement

    Ethernet Printer Technical Manual November 10, 2010 10. Ethernet Card Replacement 10.1 A-2240E Ethernet Card Replacement Turn off the printer. Remove the 2 screws (I) on the bottom of the printer (39). Pull out the front side of the “Middle Cover” (27) then remove it from “Bottom” (39) as shown in Fig.
  • Page 33 Ethernet Printer Technical Manual November 10, 2010 Remove the 4 screws (E). Unplug all the connectors that are connected on the main board. Then remove the “Printer Chassis” (30) as shown in Fig. 10.1.2. Figure 10.1.2 Remove the 4 screws (B) which fix the main board (43) from the bottom (39). Then remove the defected main board as shown in Fig.

  • Page 34: X-2300E/X-3200E Ethernet Card Replacement

    Ethernet Printer Technical Manual November 10, 2010 Pull out the Ethernet card (93) from the main board, and then insert the new Ethernet card (93) to main board as shown in Fig. 10.1.4. Figure 10.1.4 Secure the 4 screws (B) to fix the main board. 10.
  • Page 35 Ethernet Printer Technical Manual November 10, 2010 4. Remove the 8 screws on the main board (Fig. 10.2.2). Figure 10.2.2 5. Replace the Ethernet card on the main board (Fig. 10.2.3). Figure 10.2.3...

  • Page 36: Cp-2140E Ethernet Card Replacement

    Ethernet Printer Technical Manual November 10, 2010 10.3 CP-2140E Ethernet Card Replacement 1. Turn off the printer. 2. Remove the 2 screws (J) on the printer bottom (71). 3. Pull out the front side of the “Middle Cover” (3) then remove it from “Bottom” (71) as shown in Fig.
  • Page 37 Ethernet Printer Technical Manual November 10, 2010 5. Remove the 2 screws (D). 6. Unplug all the connectors that are connected to the main board. Then remove the “Printer Chassis” (29) as shown in Fig. 10.3.2. Figure 10.3.2 7. Remove the 8 screws (D) which fix the main board (69) from the bottom (71). Then remove the defected main board as shown in Fig.
  • Page 38 Ethernet Printer Technical Manual November 10, 2010 Figure 10.3.3 8. Remove the Ethernet card (82) from the main board, and then insert the new Ethernet card (82) to the main board as shown in Fig. 10.3.4. Figure 10.3.4 9. Secure the 8 screws (C) to fix the main board. 10.

  • Page 39: Os-2130De Ethernet Card Replacement

    Ethernet Printer Technical Manual November 10, 2010 10.4 OS-2130DE Ethernet Card Replacement 1. Turn off the printer power; unplug the power cable and the USB/Ethernet/Serial cable. 2. Remove the top cover. 3. Remove the 2 screws on the base housing.

  • Page 40: Printer Utility

    Ethernet Printer Technical Manual November 10, 2010 11. Printer Utility 11.1 Download/Upgrade firmware 1. Choose the printer that you want to upgrade firmware or send files, then select LAN on the Interface option.
  • Page 41 Ethernet Printer Technical Manual November 10, 2010 2. Enter the IP address. Now, you can upgrade firmware or send files similar with other printer operations.

  • Page 42: Printer Setting

    Ethernet Printer Technical Manual November 10, 2010 11.2 Printer setting If there an error occurs, the computers will simultaneously receive the error message via the Router. (Fig.11.2.1) Route Media out Ribbon out Printer Printer Printer Fig.11.2.1 If the printer is directly connected to the PC using the Internet cable (the IP address must be set first), turn on the printer.
  • Page 43 Ethernet Printer Technical Manual November 10, 2010 To enable the SNMP function, select Ethernet SNMP on Port option.
  • Page 44 0x07 Cutter fail 0x08 TPH open 0x09 TPH too hot 0x0a~0x2f Argox define 0x30~0x7F User define 0x80~0xFF Other define Example 1: If the media out occurs and the printer responds “0x01 0x01”; that indicates 1 media out error has occurred.
  • Page 45 Ethernet Printer Technical Manual November 10, 2010 11.3 Printer Info 1. Click the Search Net Printer button. On the Printer Info tab, the printer IP address is displayed.
  • Page 46 Ethernet Printer Technical Manual November 10, 2010 2. To display more information about the net printer, click the “+” on the Net Printer. Click the Go to Homepage button. 3. The webpage below appears on the screen.
  • Page 47 Ethernet Printer Technical Manual November 10, 2010 12. SELF-TEST DIAGNOSIS 12.1 Perform Self-test Diagnosis When the printer is first installed, a self test should be performed. To perform the self test, please follow the below procedures: Turn off the power. Load the media (and ribbon, if using thermal transfer media instead of direct thermal paper) properly.
  • Page 48 Ethernet Printer Technical Manual November 10, 2010 7. H. position adjust Sets the horizontal offset when printing. 8. Sensor type Displays sensor type in use - See-Through or Reflective. 9. Label-less Calibration Value Checks whether the printer performs a label-less calibration or not. If not, it should be 0000. 10.
  • Page 49 Ethernet Printer Technical Manual November 10, 2010 19. Cut Count Displays the amount of labels that the printer cuts off. 20. RS232 Protocols Displays the data frame of the RS-232 interface: baud rate, parity, data bit, and stop bit. 21. Control Character Displays the caret, delimiter and tilde control characters.
  • Page 50 Ethernet Printer Technical Manual November 10, 2010 of a single Internet Protocol network. The process of sub netting is the division of a computer network into groups of computers that have a common, designated IP address routing prefix. 32. Gateway Displays the gateway address.
  • Page 51 Ethernet Printer Technical Manual November 10, 2010 Figure 12.1.

This manual is also suitable for:

X-2300eX-3200eA-2240eCp-2140e

Table of Contents