Haier XQS50-28 User Manual page 6

Useage the drain hose
Before using , hang up the drain hose on suitable location.
Do not put down the drain hose on the ground.
Confirm the end of drain hose is higher than the level
of tub . If not the siphon will being .
How to change the direction of the drain hose
1. Dismount the back cover of the washing machine.
2. Take off the drain hose frame. Put down the drain
hose. Take off the drain hose rack. As indicated
in Figure 1, put the drain hose into the cabinet.
Then put one hand into the cabinet to nip the claw
of the drain hose bushing to release the claw from
original position. Take off the drain hose bushing
with the other hand. (As indicated in Figure 2 and 3).
• • • • • ••••• •••• • • •• • ••••• ••••• ••
••••• ••••• • • •• •
••••• ••••
••••• ••••• • ••• ••••••• • ••• • ••••
•••••• •
•••••• •
••••••
• •••• •••••
••••• •••• ••••• ••
••••
•••• •• •
•••• ••••• •• •• ••
••••
•••••• •
Attention: To guarantee the proper installation, it is suggested to have the direction changing of drain
hose performed by the after-sales service technicians of our company.
Before Using Before Using
<1.2m
3. Dismount the protecting cover of the drain
outlet at the other side ( method the same as
the drain hose bushing). Install the drain hose
bushing as per indicatedin Figure 4.
4. Extend the drain hose from the other side.
Fix the drain hose onto the cabinet with the
drain hose rack. (As indicatedin Figure 5) Take
on the drain hose frame , hang up .
••••• ••••• • ••••••
•••••• •
•••••• •
5. Install the drain hose protecting cover on
the other side.(As indicatedin Figure 6) .
•••••• •
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically. To select other procedures, push the "soak", " wash", " rinse" or "spin" button
to select the time of soak, wash and spin, and the times of rinse. After switching on the power, if you
push one of the button among "wash", "rinse"and"spin", the digitron of the former procedures will
turn off automatically. The former procedures will not run. For instance: after switching on the power. If
you push the "spin" button first, it will execute spin singly after starting.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to selected water level.
The soak procedure can work in cooperation with automatic programs like standard, jeans, chemical fiber and
cotton.There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
Press " WATER LEVEL "button,select suitable
water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level. Refer to "standard dosage of detergent and
water quantity"in Page 9 and "water level button"in Page 11 for selection.
Page 9
Water Level and Time Table for Each Program (self programming not included)
Program Water Wash Rinse (min/time)
level (min)
Standard 1-10 About Save water program, total 10 around
10-16
Quick 1-10 About 5 Save water program, total 10 around
Super quick 3 About 2 Save water program, total 4 around
Jeans 1-10 About 20 Rinse twice, about 5 each
time
Chemical fiber 1-10 About 12 Rinse twice, about 3
Cotton 1-10 About 10 Rinse twice, about 3
Wool 1-10 About 3 Rinse twice, about 2
Silk 1-10 About 5 Rinse twice, about 2
Using process Using process
WATER
LEVEL
Page 11
Spin (min) Total time
(min)
About 19-25
About 15
About 6
About 6 About 54
About 4 About 41
About 4 About 49
About 3 About 24
About 3 About 30